|
dsc08960
Stb side after layups and peel ply removed.
Date: 10/01/2012
Views: 10356
|
|
|
2012-08-18_19-58-42_666
Port side. Same area as before just without the flash. Backlit from the inside to show areas with less material. This is before I did the belly layup per the manual.
Date: 08/19/2012
Views: 10114
|
|
|
dsc08961
Stb side two layers bid 10" and 8" peel ply removed
Date: 10/01/2012
Views: 10055
|
|
|
dsc08962
Stb side. Need to do some clean up...
Date: 10/01/2012
Views: 10037
|
|
|
dsc08642
From the start the airframe was sitting 2.5 deg tail low and 0.1 deg to port. Not bad for just putting her on there. I jacked up the back of the trailer to get it as near to 0.0 as possible and also shifted the airframe latterly to turn that .1 to 0.0 a
Date: 04/15/2012
Views: 9682
|
|
|
2012-08-18_19-58-15_689
Port side. Red highlighted area shows area with little reinforcement on inside. This is before I did the belly layup per the manual.
Date: 08/19/2012
Views: 9593
|
|
|
dsc08625
Cutting out one of the ribs for the airframe. Going to use the mono trailer as the foundation of the jig. This will make is easy to level the airframe when getting ready for the trr-gear conversion. How do you like my work bench?
Date: 04/14/2012
Views: 9482
|
|
|
dsc08626
Put in a 2x4 in the main wing spar tunnel and located the pins. This was only used to aid in keeping the plane from tipping.
Date: 04/14/2012
Views: 9417
|
|
|
dsc08966
Port side LG socket hole.
Date: 10/01/2012
Views: 9160
|
|
|
20141102_152814
Drilling out the screw. It would move. I'm removing this plate to patch later.
Date: 11/02/2014
Views: 8835
|
|
|
dsc08627
The monowheel landing gear is in the up position and resting on the main wheel with some of the weight held by the block and tackle. This was taken just before putting on the braces to keep her from rolling. Been trying to get rid of that tv in the back
Date: 04/14/2012
Views: 8605
|
|
|
dsc08965
Port side after layups and peel ply removed. Notice shape of hole for the angle of the LG socket. I wrapped the LG socket with sandpaper and used it to form the hole.
Date: 10/01/2012
Views: 8542
|
|
|
DSC08800
starboard side
Date: 06/05/2012
Views: 8466
|
|
|
DSC08797
Port side
Date: 06/05/2012
Views: 8426
|
|
|
dsc08967
Little clean up required on Port side.
Date: 10/01/2012
Views: 8405
|
|
|
DSC08801
starboard side
Date: 06/05/2012
Views: 8398
|
|
|
DSC08799
Port side
Date: 06/05/2012
Views: 8236
|
|
|
dsc08963
Port side. LG socket fitting.
Date: 10/01/2012
Views: 8077
|
|
|
dsc09018
Started to make the axle jig. Used a simple setup of first taking large flat blocks of wood and caulking it to the floor somewhere over FS70. Then that allows me to fix the aluminum angle with a single screw once in its final position.
Date: 01/10/2013
Views: 8077
|
|
|
dsc08607
Starting to prep the bays for the tri-gear conversion.
Date: 04/10/2012
Views: 8065
|
|