|
IMG_1304
Inside fitting
Date: 04/14/2011
Views: 2586
|
|
|
IMG_1305
Outside fitting
Date: 04/14/2011
Views: 2722
|
|
|
IMG_1303
Fitting the wheel pants. Here, I'm using a mirror to see where the tire rubs on the opening so I can mark areas to relieve.
Date: 04/14/2011
Views: 2201
|
|
|
IMG_1299
Began the process of making up mounts for the wheel pants.
Date: 04/11/2011
Views: 2393
|
|
|
IMG_1300
Test mount for the wheel pants.
Date: 04/11/2011
Views: 2438
|
|
|
IMG_1301
Test fit of the console cover.
Date: 04/11/2011
Views: 2582
|
|
|
IMG_1667
This had not been done on my quick build cockpit module. Next will be to add the two plies of BID.
Date: 04/13/2011
Views: 2434
|
|
|
IMG_1668
Began fitting the brake fluid reservoir.
Date: 04/13/2011
Views: 2711
|
|
|
IMG_1669
Evaluating how the reservoir will be mounted/attached.
Date: 04/13/2011
Views: 2692
|
|
|
IMG_1666
Bonded the bushing reinforcements onto the cockpit module bushings
Date: 04/13/2011
Views: 2708
|
|
|
1_snaps
The snap bases for the seat back cushions were poorly installed by my interior guy. Just a skinny screw through the over-sized hole the snap base where the original rivet went.
Date: 06/23/2011
Views: 3917
|
|
|
2_snaps
When the tab on the back of the pilot cushion was pulled to remove it, the snap bases pulled through the screw head and remained in the snaps. You should be able to see the snap bases in the snaps in this picture.
Date: 06/23/2011
Views: 3838
|
|
|
3_snaps
The original snap base hardware is on the right. The new snap bases and mounting hardware are on the left. These 6-32 screw mount snap bases are from McMaster-Carr. I used big ol' AN970 washers for more support underneath and nyloc nuts so they don't c
Date: 06/23/2011
Views: 3570
|
|
|
4_snaps
Here is a picture of the original snap bases still on the passenger head rest along with one of the new screw snap bases.
Date: 06/23/2011
Views: 3780
|
|
|
5_snaps
The new snap bases installed in the head rest.
Date: 06/23/2011
Views: 3837
|
|
|
6_snaps
Seat cushions installed and snapped into place.
Date: 06/23/2011
Views: 3750
|
|
|
2_Door_Knobs
They work well without any protruding or scratch making lumps or bumps.
Date: 06/23/2011
Views: 3328
|
|
|
3_Door_Knobs
Similarly, the screw portion is nice and flat so it won't hang up on the aluminum guard plate when pressed closed.
Date: 06/23/2011
Views: 4437
|
|
|
1_Door_Knobs
The new door knob mounting hardware is a stainless steel "binding post" acquired from McMaster-Carr. These things are available in myriad materials and sizes. There just happened to be a perfect size in the stainless steel variety which I pref
Date: 06/23/2011
Views: 3966
|
|
|
IMG_1283ann
The starboard wheel pant with all the tape and poly removed. Almost ready for anchor nuts and screws. Unfortunately, I left one area of the flange too thing and had to add small pieces of glass. Tomorrow will be anchor nut day for it.
Date: 03/30/2011
Views: 2378
|
|