|
IMG_1216ann
Date: 06/13/2010
Views: 2948
|
|
|
IMG_9562ann
2010 06 06 - Made up an adaptor that fits the bleed and doesn't leak. Began to run fluid into the system. Went up to the master cylinder/reservoir to check on progress. Was I getting bubbles through the bit of fluid it put in back on the 3rd?
Date: 06/06/2010
Views: 2716
|
|
|
IMG_9556ann
What the heck... There were dead bugs all over the master cylinder. What's going on here. Get out a light, the brake fluid reservoir is full of dead bugs! $#!&$%@%^&*%@$#%%&*&^@$%@%$%$@^#$%^!!!!! Seems that wile I was spending a month
Date: 06/06/2010
Views: 2728
|
|
|
IMG_9557ann
I dug out a bunch, and came to the conclusion that I'm going to have to order a new brake line and clean out the master cylinder before I can continue here. So I went on to the new mechanical fuel pump installation...
Date: 06/06/2010
Views: 2662
|
|
|
IMG_9534ann
Date: 06/03/2010
Views: 2639
|
|
|
IMG_9536ann
Date: 06/03/2010
Views: 2839
|
|
|
IMG_1195ann
Date: 05/31/2010
Views: 2900
|
|
|
IMG_1193ann
Date: 05/31/2010
Views: 2830
|
|
|
IMG_1167ann
Went to the hanger after work and put the brake back together. Seems to work fine. I have not safety wired it yet as I want to add fluid, bleed and give it a good test beforehand. When all tests wel,l with no leaks, I'll wire it up. Could have used a
Date: 04/19/2010
Views: 2659
|
|
|
IMG_7530ann
First try was just to bolt the BSPP banjo onto the brake. Needless to say, that was just too simple to work. It wouldn't seat properly in the BSPT brake.
Date: 04/18/2010
Views: 2702
|
|
|
IMG_7539ann
Realizing that I'd need to do any remaining work at home, I removed the disk brake, gathered up the bits and headed for the shop. This is just a pic of the BSPT threaded hole in the disk brake. Had to clean it out as it was full of crap. Testing showed
Date: 04/18/2010
Views: 2644
|
|
|
IMG_7540ann
That leaves two choices: #1 - tap the brake in BSPP threads or #2 - run the BSPT die over the bolt to thread in BSPT. The brake being aluminum and the bolt being stainless steel, I decided to go with #1 as it seemed easier.
Date: 04/18/2010
Views: 2631
|
|
|
IMG_7541ann
It took almost an hour to carefully and safely get the tap started in the aluminum brake. I sure didn't want to screw that up. Once I had a good start and the tap began to cut, I clamped the tap in the vice with the brake held high so chips fall out and
Date: 04/18/2010
Views: 2527
|
|
|
IMG_7543ann
The final result. The banjo hose end bolts nicely to the brake. With any luck, I'll take the brake back to the airport after work tomorrow and reinstall it all and see if I can bleed the brakes.
Date: 04/18/2010
Views: 2872
|
|
|
IMG_7529ann
The new BSPP (British Standard Pipe Parallel) banjo bolts finally arrived from Speed Flow of Australia last week. Due to a death in the family and illnesses, I haven't gotten back to working on the Europa for several weeks. But I did today. I had also
Date: 04/18/2010
Views: 2596
|
|
|
IMG_7441post
Here's a look at the tubing end of the two fittings. Again, similar, but not the same. Can't use the original fitting with the new tubing.
Date: 03/19/2010
Views: 2476
|
|
|
IMG_7440post
2010 03 19 - Checked to see if the new brake banjo hardware would work while completing the Annual Condition Inspection on the Europa. This is a comparison of the original fitting from the brake with the new banjo bolt that's supposed to work. Close, bu
Date: 03/19/2010
Views: 2811
|
|
|
IMG_7429post
Here's a closeup of the hose end, bolt and washers. The hose end connector is identical to that which was on the master cylinder end so this should easily replace the 90 degree AN hose end provided. We'll know better later this week when I can get to th
Date: 03/15/2010
Views: 2492
|
|
|
IMG_7428post
My new banjo hose end for the brake arrived today. Good work Merlin Motor Sports.
Date: 03/15/2010
Views: 2575
|
|
|
IMG_7383ann
The Issue, Continued... The blue Tee connector shown has a 3/8 NPT thread on the upper leg. it is a 3/8 x 24 National Pipe Thread. That is, it has a tapered thread. The thread measures 0.373 in on the narrow end and 0.408 in on the wide end. The othe
Date: 03/07/2010
Views: 2561
|
|