|
IMG_1471ann
2011 01 27 One final check of alignment before drilling.
Date: 01/27/2011
Views: 3131
|
|
|
IMG_0822ann
Set to drilling and bolting the new outer brackets in place.
Date: 01/27/2011
Views: 3297
|
|
|
IMG_0823ann
the other flap bracket.
Date: 01/27/2011
Views: 3275
|
|
|
IMG_0824ann
Somewhere along the way, a couple spacers had been lost. Made up new ones. Also put anchor nuts on the radiator mounting flanges to make assembly easier, sorta, kinda. Seems like reassembling this aircraft is more difficult than the original building.
Date: 01/27/2011
Views: 3327
|
|
|
IMG_1426ann
2010 12 21 - Taking advantage of a couple days of nice weather. Installed the cooling duct and heat exchangers.
Date: 12/21/2010
Views: 3186
|
|
|
IMG_1431ann
Continuing work on the fill/sand
Date: 12/21/2010
Views: 3615
|
|
|
IMG_1593ann
Installed the master cylinder and parking brake and began connecting brake lines.
Date: 03/16/2011
Views: 3663
|
|
|
IMG_1595ann
Test fit of the intercooler.
Date: 03/16/2011
Views: 3184
|
|
|
IMG_1423ann
Ran the left and right brake line up through the tunnel.
Date: 12/20/2010
Views: 3452
|
|
|
IMG_1418ann
I had also been working on a stainless steel cover/mount which attaches to the lower firewall and will support the front edge of the monowheel hole cover.
Date: 12/20/2010
Views: 3296
|
|
|
IMG_1425em
Just kind of a status photo as of 2010 12 20
Date: 12/20/2010
Views: 3214
|
|
|
IMG_1412ann
2010 12 20 It's difficult to work in the hanger during the cold of late November and all of December. I tended to stay home and work in the shop on the "Taz" the Little Toot Sport Biplane I'm building. On the occasional nice day like this I ma
Date: 12/20/2010
Views: 3371
|
|
|
IMG_0767ann
2010 11 23 Began putting the baffle/supports back on.
Date: 11/23/2010
Views: 3823
|
|
|
IMG_0766ann
Baffle/supports screwed down and safety wired.
Date: 11/23/2010
Views: 3238
|
|
|
IMG_0768ann
Also bonded the parking brake mount in place.
Date: 11/23/2010
Views: 3023
|
|
|
IMG_1371ann
2010 11 17 Had some leftover SuperFil from wing work so I cleaned up the holes in the tail where the old tailwheel cables exited the aft fuselage and proceeded to fill them.
Date: 11/17/2010
Views: 3067
|
|
|
IMG_1373ann
For the last several days I had been making up a cover for the monowheel hole. Here it's ready for a test fit and any adjustments necessary.
Date: 11/17/2010
Views: 3322
|
|
|
IMG_1374ann
I also received the new parts for the Rotax oil pressure regulator so I replaced them and safety wired it all back together.
Date: 11/17/2010
Views: 3359
|
|
|
IMG_1364ann
2010 11 13 I began the fill/sand routine on the patched areas of the wing.
Date: 11/13/2010
Views: 2850
|
|
|
IMG_1362ann
2010 11 12 Was a total waste of a day. After arriving at the hanger, I went in to open the hanger door. When the hanger door had been opened I was greeted by the sight of a drooping rear bumper on the Ranger. Went to the droopy side and found this. R
Date: 11/12/2010
Views: 4429
|
|