|
dsc09056
Wetting out stbd side.
Date: 01/24/2013
Views: 8123
|
|
|
dsc08617
After removing the green tape.
Date: 04/14/2012
Views: 68636
|
|
|
dsc09070
While the layups are curing we stared work on the axles. Had to ream out the holes forMG02.
Date: 01/25/2013
Views: 8549
|
|
|
dsc09048
Template for the Stbd side. Note, you are not required per the manual to hook over the plywood with bid.
Date: 01/24/2013
Views: 8537
|
|
|
dsc08602
Landing gear parts. The nose gear leg is having MOD 53 performed on it at my fauther in-laws.
Date: 04/10/2012
Views: 9353
|
|
|
nex_2014_01_25_03
Port side dirty work. Just test fitting final install with all hardware will be after the legs are painted.
Date: 01/25/2014
Views: 7807
|
|
|
dsc08636
Here is Bill placing in some 2x6's to act as a support for the rear rib. The I-beam is 3 inches wide so the 2x6 fit perfectly. I'll explain later how those come into play.
Date: 04/15/2012
Views: 7771
|
|
|
nex_2014_01_25_16
nex_2014_01_25_16.jpg
Date: 01/25/2014
Views: 7711
|
|
|
p1000468
p1000468.jpg
Date: 12/09/2011
Views: 33768
|
|
|
dsc08967
Little clean up required on Port side.
Date: 10/01/2012
Views: 10038
|
|
|
p1000730
p1000730.jpg
Date: 03/12/2012
Views: 6261
|
|
|
Close up of the relief cut.
Close up of the relief cut.
Date: 04/03/2016
Views: 13864
|
|
|
dsc09028
Here the axles are getting the green goop. I used car carnauba wax as a release agent. Worked well jut get it on there thick. We also wrapped the top of the sockets with glad wrap to keep contaminates off of it while we moved it around.
Date: 01/22/2013
Views: 9192
|
|
|
dsc08639
More of the same. I was going to cut the carpet and form it to the ribs and staple it in place but decided that was just a time vampire and pointless since the airframe is holding it in place.
Date: 04/15/2012
Views: 8259
|
|
|
p1000697
p1000697.jpg
Date: 03/12/2012
Views: 6930
|
|
|
p1000722
p1000722.jpg
Date: 03/12/2012
Views: 6721
|
|
|
dsc08612
Unused Mono wheel components. I'll probably be selling these soon.
Date: 04/10/2012
Views: 12019
|
|
|
dsc09051
Mix it up Kim! FYI I hate this scale from aircraft spruce, it times out in one min if your plugged in or not. I would have to tap the scale while Kim mixed. We were using masks due to being in an enclosed area and I'm very allergic to the hardener (bumm
Date: 01/24/2013
Views: 8651
|
|
|
20141102_161049
20141102_161049.jpg
Date: 11/02/2014
Views: 14725
|
|
|
nex_2013_08_24_03
nex_2013_08_24_03.jpg
Date: 08/25/2013
Views: 7185
|
|