|
IMG_0094post
Date: 09/03/2010
Views: 2573
|
|
|
IMG_0053post
Date: 09/01/2010
Views: 3439
|
|
|
IMG_0031post
Date: 08/30/2010
Views: 3297
|
|
|
IMG_0132post
Date: 09/03/2010
Views: 2703
|
|
|
IMG_0923ann
2011 03 02 Darn cold winter this year. Start to fit the last piece of baffle back in place. Needless to say, it's fighting back.
Date: 03/02/2011
Views: 2654
|
|
|
2_Door_Knobs
Nice low profile head
Date: 06/23/2011
Views: 3179
|
|
|
New MC-4A02
And it's too wide to fit in between the mounts. I have 1 1/4 x 1 1/4 x 1/8 Al angle on order to fix the width problem and I think I know how to fix the length problem as well. Then I can address the height issue...
Date: 04/11/2012
Views: 2892
|
|
|
IMG_1412
Another issue with the pre-built cockpit module. The fuel tank was not supported on the aluminum angle. Bud suggested this could cause tank cracking and recommended some sort of support be added. I cut a wedge from a length of balsa and covered it with
Date: 05/28/2011
Views: 3160
|
|
|
IMG_0184post
Date: 09/07/2010
Views: 2542
|
|
|
New MC-4A 05
With the attach fitting fully screwed on to the end of the thread, the last bit of thread is just visible in the fitting.
Date: 04/12/2012
Views: 2799
|
|
|
IMG_0039post
Date: 09/01/2010
Views: 3343
|
|
|
IMG_1300
Test mount for the wheel pants.
Date: 04/11/2011
Views: 2849
|
|
|
IMG_0151post
Date: 09/04/2010
Views: 2805
|
|
|
New MC-4A 12
The whole assembly should now fit, length and width, within the existing space. So the unit may be dropped down as needed to allow for it being taller. Due to outside commitments, it looks like it will be Wednesday (18th) before I can get to the hanger
Date: 04/15/2012
Views: 3097
|
|
|
IMG_3577post
Next test, connect high pressure port from airbox directly to the "T" into the carb float bowl pressure lines and try a run. Still didn't work. Same smooth up to 4200/4300 RPM, smooth drop to 3200 RPM, smooth acceleration up to 4300 RPM, drop
Date: 08/03/2012
Views: 7980
|
|
|
IMG_0455ann
Hole cut in console to accomodate the new brake levers.
Date: 10/18/2010
Views: 3177
|
|
|
IMG_1418ann
I had also been working on a stainless steel cover/mount which attaches to the lower firewall and will support the front edge of the monowheel hole cover.
Date: 12/20/2010
Views: 3261
|
|
|
New MC-4A 11
Because the sides are narrower and closer to the ends of the MC-4A's the old outer spacers no longer fit and it would be impossible to further shorten them, they have been replaced with a couple washers.
Date: 04/15/2012
Views: 5787
|
|
|
IMG_1499ann
2011 02 18 Weather remains cold overall. Today was nice though. Mounted a number of new cable tie mounts to hold wires, etc.
Date: 02/18/2011
Views: 3021
|
|
|
Flap Mark Test Up
Started the application of the flap position marking with a printer copy to test for proper placement.
Date: 07/01/2011
Views: 3314
|
|