|
p1000627
p1000627.jpg
Date: 02/14/2012
Views: 7477
|
|
|
p1000692
p1000692.jpg
Date: 03/12/2012
Views: 5988
|
|
|
p1000708
p1000708.jpg
Date: 03/12/2012
Views: 5960
|
|
|
nex_2014_01_25_03
Port side dirty work. Just test fitting final install with all hardware will be after the legs are painted.
Date: 01/25/2014
Views: 7802
|
|
|
nex_2014_01_25_02
Starboard side of the air bubble fix on rib one. Used Flox with aeroboxy as a fillit.
Date: 01/25/2014
Views: 7670
|
|
|
nex_2014_01_12_05
Port side top.
Date: 01/13/2014
Views: 7434
|
|
|
nex_2014_01_25_01
Starboard side after Uni over ribs 3 and 4. Added Bid on the X to reinforce the cuts needed to get the Uni to lay flat. Also filled in Rib 1 air buble.
Date: 01/25/2014
Views: 7457
|
|
|
dsc09036
Rib one port side again used around 112g of 420 cured at 78f for 12 hours.
Date: 01/23/2013
Views: 8543
|
|
|
dsc08639
More of the same. I was going to cut the carpet and form it to the ribs and staple it in place but decided that was just a time vampire and pointless since the airframe is holding it in place.
Date: 04/15/2012
Views: 8255
|
|
|
dsc08962
Stb side. Need to do some clean up...
Date: 10/01/2012
Views: 11654
|
|
|
p1000689
p1000689.jpg
Date: 03/12/2012
Views: 6858
|
|
|
dsc08967
Little clean up required on Port side.
Date: 10/01/2012
Views: 10033
|
|
|
dsc08627
The monowheel landing gear is in the up position and resting on the main wheel with some of the weight held by the block and tackle. This was taken just before putting on the braces to keep her from rolling. Been trying to get rid of that tv in the back
Date: 04/14/2012
Views: 10927
|
|
|
dsc09072
Here is a shot of the working angle. This was so much better than leaning over the edge. Kim's idea. Notice the heater behind Kim, this was key to keeping the temps even though the temps outside were in the 40's.
Date: 01/26/2013
Views: 8713
|
|
|
nex_2014_01_25_07
What a mess.
Date: 01/25/2014
Views: 7773
|
|
|
dsc08625
Cutting out one of the ribs for the airframe. Going to use the mono trailer as the foundation of the jig. This will make is easy to level the airframe when getting ready for the trr-gear conversion. How do you like my work bench?
Date: 04/14/2012
Views: 11946
|
|
|
p1000473
p1000473.jpg
Date: 12/13/2011
Views: 13736
|
|
|
dsc09034
Starboard side done. Pic taken before a little clean up.
Date: 01/22/2013
Views: 7941
|
|
|
p1000617
p1000617.jpg
Date: 01/29/2012
Views: 9779
|
|
|
NEX_2013-11-12-37
N111EU at rest.
Date: 11/13/2013
Views: 32108
|
|