|
dsc08636
Here is Bill placing in some 2x6's to act as a support for the rear rib. The I-beam is 3 inches wide so the 2x6 fit perfectly. I'll explain later how those come into play.
Date: 04/15/2012
Views: 7337
|
|
|
dsc08621
Removal of the brake master for the mono.
Date: 04/14/2012
Views: 17070
|
|
|
dsc09047
I took cardboard and bent it around the socket and overlapped per the manual. Then took this cardboard and made a new template for cutouts. This made the layups go really quick.
Date: 01/23/2013
Views: 8324
|
|
|
p1000721
p1000721.jpg
Date: 03/12/2012
Views: 6954
|
|
|
dsc09051
Mix it up Kim! FYI I hate this scale from aircraft spruce, it times out in one min if your plugged in or not. I would have to tap the scale while Kim mixed. We were using masks due to being in an enclosed area and I'm very allergic to the hardener (bumm
Date: 01/24/2013
Views: 8247
|
|
|
dsc09018
Started to make the axle jig. Used a simple setup of first taking large flat blocks of wood and caulking it to the floor somewhere over FS70. Then that allows me to fix the aluminum angle with a single screw once in its final position.
Date: 01/10/2013
Views: 9389
|
|
|
dsc08965
Port side after layups and peel ply removed. Notice shape of hole for the angle of the LG socket. I wrapped the LG socket with sandpaper and used it to form the hole.
Date: 10/01/2012
Views: 9765
|
|
|
DSC08796
Put in the panel to dream a little. Don't really know what I'm going to do. Was thinking of keeping it low cost for the first panel and keeping it analog until I can get the cash mula for something better like glass/IFR. Also want to fill the hole where
Date: 06/05/2012
Views: 11797
|
|
|
p1000692
p1000692.jpg
Date: 03/12/2012
Views: 5920
|
|
|
dsc09061
Applying the layups on stbd side.
Date: 01/24/2013
Views: 8054
|
|
|
dsc09057
Wetting out stbd side.
Date: 01/24/2013
Views: 7938
|
|
|
Actual part.
Actual part.
Date: 04/03/2016
Views: 13556
|
|
|
dsc08634
OK now that the plane is off the trailer and on its own wheel we were able to remove most of the trailer hardware and position the ribs. We also used the main bolts to hold the first rib in place. The other rib was left a little lower to be located once
Date: 04/15/2012
Views: 7502
|
|
|
p1000728
p1000728.jpg
Date: 03/12/2012
Views: 6329
|
|
|
dsc08602
Landing gear parts. The nose gear leg is having MOD 53 performed on it at my fauther in-laws.
Date: 04/10/2012
Views: 8905
|
|
|
dsc09054
Wetting out stbd side.
Date: 01/24/2013
Views: 7700
|
|
|
p1000690
p1000690.jpg
Date: 03/12/2012
Views: 6324
|
|
|
dsc08627
The monowheel landing gear is in the up position and resting on the main wheel with some of the weight held by the block and tackle. This was taken just before putting on the braces to keep her from rolling. Been trying to get rid of that tv in the back
Date: 04/14/2012
Views: 10355
|
|
|
dsc09042
Starboard side being keyed.
Date: 01/23/2013
Views: 7605
|
|
|
dsc08619
Roap tied to the engine mount frame to hoist the airframe.
Date: 04/14/2012
Views: 15524
|
|