|
IMG_7269post
Date: 02/21/2010
Views: 3401
|
|
|
IMG_1215ann
Date: 06/13/2010
Views: 3206
|
|
|
IMG_6690Ann
Date: 02/15/2008
Views: 3534
|
|
|
IMG_0037
More retraction tests. Closer, but still won't quite go into up lock. Maybe 1/4" (0.635 cm) from engaging. Back under for a couple more hours before I finally see where the blue from the fitting is rubbing on the side of the tunnel where the seat
Date: 07/07/2010
Views: 3285
|
|
|
DSCN6122Ann
Date: 06/14/2007
Views: 3158
|
|
|
IMG_7384ann
The threads on both fittings are 24/in. So that's a match. The issue is one is straight and the other pipe thread.
Date: 03/07/2010
Views: 3082
|
|
|
IntercoolerFig2
Date: 01/07/2006
Views: 3386
|
|
|
IMG_6687Ann
Date: 02/15/2008
Views: 4262
|
|
|
LongRangeTankBoM
Date: 07/31/2004
Views: 4210
|
|
|
IMG_1235ann
2010 06 21 - The new Billet pump and regulator arrived so I went out to the hanger and installed it. The new pump and regulator were supplied with AN6 Flared Tube fittings this time so the exchange was trivial. Must have taken all of 5 minutes.
Date: 06/21/2010
Views: 3923
|
|
|
IMG_6695Ann
Date: 02/15/2008
Views: 3967
|
|
|
IMG_9556ann
What the heck... There were dead bugs all over the master cylinder. What's going on here. Get out a light, the brake fluid reservoir is full of dead bugs! $#!&$%@%^&*%@$#%%&*&^@$%@%$%$@^#$%^!!!!! Seems that wile I was spending a month
Date: 06/06/2010
Views: 3143
|
|
|
DSCN6117Ann
Date: 06/14/2007
Views: 3268
|
|
|
IMG_6684Ann
Date: 02/15/2008
Views: 3770
|
|
|
DSCN6112Ann
Date: 06/13/2007
Views: 3079
|
|
|
IMG_7378ann
2010 03 07 - Spent Saturday working on the new brake master cylinder from MDO in France. I have it about 75% installed. Ran into some hardware issues which are shown in later pics. This pic is an overview of the new master cylinder installed on the con
Date: 03/07/2010
Views: 3206
|
|
|
IMG_2857
Date: 12/03/2008
Views: 3446
|
|
|
IMG_7440post
2010 03 19 - Checked to see if the new brake banjo hardware would work while completing the Annual Condition Inspection on the Europa. This is a comparison of the original fitting from the brake with the new banjo bolt that's supposed to work. Close, bu
Date: 03/19/2010
Views: 3229
|
|
|
IMG_9562ann
2010 06 06 - Made up an adaptor that fits the bleed and doesn't leak. Began to run fluid into the system. Went up to the master cylinder/reservoir to check on progress. Was I getting bubbles through the bit of fluid it put in back on the 3rd?
Date: 06/06/2010
Views: 3031
|
|
|
IMG_7560Ann
Dan at Billet sent a couple AN-6 adaptors to replace the hose barbs.
Date: 04/30/2010
Views: 3374
|
|