|
p1000729
p1000729.jpg
Date: 03/12/2012
Views: 5968
|
|
|
dsc08639
More of the same. I was going to cut the carpet and form it to the ribs and staple it in place but decided that was just a time vampire and pointless since the airframe is holding it in place.
Date: 04/15/2012
Views: 7293
|
|
|
dsc09018
Started to make the axle jig. Used a simple setup of first taking large flat blocks of wood and caulking it to the floor somewhere over FS70. Then that allows me to fix the aluminum angle with a single screw once in its final position.
Date: 01/10/2013
Views: 8888
|
|
|
nex_2014_01_25_07
What a mess.
Date: 01/25/2014
Views: 6818
|
|
|
p1000695
p1000695.jpg
Date: 03/12/2012
Views: 5756
|
|
|
dsc08621
Removal of the brake master for the mono.
Date: 04/14/2012
Views: 15588
|
|
|
20141102_154450
Gear cover removed, now for removing the throttle box. This is all prep work to patch up the mono wheel hole.
Date: 11/02/2014
Views: 15231
|
|
|
nex_2013_08_24_03
nex_2013_08_24_03.jpg
Date: 08/25/2013
Views: 6390
|
|
|
dsc09072
Here is a shot of the working angle. This was so much better than leaning over the edge. Kim's idea. Notice the heater behind Kim, this was key to keeping the temps even though the temps outside were in the 40's.
Date: 01/26/2013
Views: 7795
|
|
|
p1000616
p1000616.jpg
Date: 01/29/2012
Views: 9160
|
|
|
dsc08633
We had to put the plane somewhat down near the trailer with the main up so that we could get the right contour for the ribs. Reminds me of a B-17 with the main just showing.
Date: 04/14/2012
Views: 6961
|
|
|
20141102_162118
Cut it out.
Date: 11/02/2014
Views: 62439
|
|
|
2012-08-18_19-58-42_666
Port side. Same area as before just without the flash. Backlit from the inside to show areas with less material. This is before I did the belly layup per the manual.
Date: 08/19/2012
Views: 10808
|
|
|
p1000698
p1000698.jpg
Date: 03/12/2012
Views: 6657
|
|
|
p1000722
p1000722.jpg
Date: 03/12/2012
Views: 6455
|
|
|
p1000637
p1000637.jpg
Date: 02/14/2012
Views: 6244
|
|
|
dsc09041
Port side guides being placed for layup.
Date: 01/23/2013
Views: 8020
|
|
|
Close up of the relief cut.
Close up of the relief cut.
Date: 04/03/2016
Views: 13043
|
|
|
nex_2014_01_25_35
Dont judge me! You know you do it too. Anyways, was trying to see if my weight would cause the nose to come down. As you can see she likes being a tail dragger.
Date: 01/26/2014
Views: 8867
|
|
|
nex_2013_08_24_01
Stb. side ribs 3 and 4 epibond in place with the 3 layups on all sides. At this point I was getting faster at doing layups however I only did one side at a time.
Date: 08/25/2013
Views: 6954
|
|