|
IMG_1280ann
Poly has been taped over the front half. This will prevent the interior layup from sticking to the front half forming the joining flange. The front and rear have been taped together in preparation for the inner layup.
Date: 03/29/2011
Views: 3057
|
|
|
New MC-4A 12
The whole assembly should now fit, length and width, within the existing space. So the unit may be dropped down as needed to allow for it being taller. Due to outside commitments, it looks like it will be Wednesday (18th) before I can get to the hanger
Date: 04/15/2012
Views: 3141
|
|
|
IMG_1493p
Port wing aileron
Date: 06/18/2011
Views: 2776
|
|
|
IMG_1262ann
2011 03 28 Propeller has been installed.
Date: 03/28/2011
Views: 3248
|
|
|
IMG_1417
Starboard wing tip
Date: 05/31/2011
Views: 3173
|
|
|
IMG_0458ann
I've gone back to the build manual and made up a pair of reinforcements. Here marking where the upholstery will be cut to make a place for them.
Date: 10/20/2010
Views: 3041
|
|
|
IMG_3367post
Request for fuel pressure input to the fuel pressure regulator. Installed a fuel pressure sensor on the input to the regulator. So now we have differential pressure out of the regulator and pressure into the regulator.
Date: 07/02/2012
Views: 4072
|
|
|
IMG_0244post
Date: 09/13/2010
Views: 2866
|
|
|
IMG_0084post
Date: 09/02/2010
Views: 2849
|
|
|
IMG_1277ann
The starboard wheel pant marked with tape to show where to cut.
Date: 03/29/2011
Views: 3375
|
|
|
IMG_1416
End of May. Applied primer to all the repaired and patched areas. Port wing outboard flap bracket area.
Date: 05/31/2011
Views: 3432
|
|
|
IMG_2598
The culprit seems to be the compressed paper gasket material which dries out if it sits for a while and then leaks. Cork gaskets were recommended as a replacement. Unfortunately, cork gaskets were not available. So I did a Google search and came up wi
Date: 05/30/2012
Views: 2960
|
|
|
IMG_3438em
There was a bit more work with the Billet pump package, but it proved not to be the problem. Moving on, OK, not the fuel system. Try running the engine as a normally aspirated engine. Remove the connection between the turbo and airbox. Believe it or
Date: 07/17/2012
Views: 5976
|
|
|
IMG_2683
Here are the new MATCO master cylinders connected to the old levers sitting on the old base. Now how do we contain the back ends to make this work?
Date: 04/07/2012
Views: 3066
|
|
|
IMG_1239ann
Looks to need another 0.445" or so.
Date: 03/25/2011
Views: 2676
|
|
|
IMG_1688
Early May. Still fitting wheel pants and gear leg fairings.
Date: 05/10/2011
Views: 3374
|
|
|
IMG_1299
Began the process of making up mounts for the wheel pants.
Date: 04/11/2011
Views: 2764
|
|
|
IMG_1400
Noticed that the underside of the starboard wing tip was scuffed. Applied filler to begin to clean it up. As well as continuing to work on pants and fairings.
Date: 05/26/2011
Views: 3191
|
|
|
IMG_1667
This had not been done on my quick build cockpit module. Next will be to add the two plies of BID.
Date: 04/13/2011
Views: 2790
|
|
|
IMG_1431ann
Continuing work on the fill/sand
Date: 12/21/2010
Views: 3615
|
|