|
dsc09024
I was really anal about keeping the socket holes tight. This proved to be more work than it was worth and was fighting the tight fit when it came to locating the axles. Do yourself a favor and just make them a little bigger, 1/8 or so. This gap will be
Date: 01/22/2013
Views: 9207
|
|
|
dsc08963
Port side. LG socket fitting.
Date: 10/01/2012
Views: 10285
|
|
|
nex_2014_01_25_28
Wings on. Not really required at the stage. Just had to do it for motivation.
Date: 01/26/2014
Views: 8285
|
|
|
nex_2013_08_24_04
As you see here the port side is done with rib 3 and 4. I didn't have photos of doing the layups.
Date: 08/25/2013
Views: 7839
|
|
|
dsc08603
Since I'm going to have to remove the mono wheel I dont have much of an edge to close in the big hole in the bottom. I'll have a better look at it once its a tri-gear.
Date: 04/10/2012
Views: 11829
|
|
|
DSC08797
Port side
Date: 06/05/2012
Views: 10278
|
|
|
dsc08611
Unused Mono wheel components. I'll probably be selling these soon.
Date: 04/10/2012
Views: 13748
|
|
|
dsc08625
Cutting out one of the ribs for the airframe. Going to use the mono trailer as the foundation of the jig. This will make is easy to level the airframe when getting ready for the trr-gear conversion. How do you like my work bench?
Date: 04/14/2012
Views: 12446
|
|
|
p1000690
p1000690.jpg
Date: 03/12/2012
Views: 6494
|
|
|
nex_2014_01_25_03
Port side dirty work. Just test fitting final install with all hardware will be after the legs are painted.
Date: 01/25/2014
Views: 8141
|
|
|
dsc09032
Port side done.
Date: 01/22/2013
Views: 8426
|
|
|
p1000707
p1000707.jpg
Date: 03/12/2012
Views: 6717
|
|
|
dsc08626
Put in a 2x4 in the main wing spar tunnel and located the pins. This was only used to aid in keeping the plane from tipping.
Date: 04/14/2012
Views: 12209
|
|
|
dsc09040
The gap from the bottom of the socket and the belly is as you see. The only way to get it all the way down was to lower the belly to 15" which was not considered an option. Belly hight is 16.0" with the axle width at 82.50" and axle cent
Date: 01/23/2013
Views: 9913
|
|
|
dsc09067
dsc09067.jpg
Date: 01/25/2013
Views: 8916
|
|
|
nex_2014_01_12_01
Bolt hole for LG port side filed to size.
Date: 01/13/2014
Views: 7685
|
|
|
dsc09019
Trash can is the best way to hold the landing gear legs.
Date: 01/10/2013
Views: 8959
|
|
|
dsc08630
Though this was a neat pic of the mono wheel in the retracted position.
Date: 04/14/2012
Views: 7917
|
|
|
p1000702
p1000702.jpg
Date: 03/12/2012
Views: 6054
|
|
|
p1000616
p1000616.jpg
Date: 01/29/2012
Views: 9776
|
|