|
p1000707
p1000707.jpg
Date: 03/12/2012
Views: 6717
|
|
|
dsc08635
Other view of the ribs.
Date: 04/15/2012
Views: 8073
|
|
|
nex_2014_01_25_01
Starboard side after Uni over ribs 3 and 4. Added Bid on the X to reinforce the cuts needed to get the Uni to lay flat. Also filled in Rib 1 air buble.
Date: 01/25/2014
Views: 7835
|
|
|
dsc09063
Hey Bill!
Date: 01/24/2013
Views: 8731
|
|
|
dsc09042
Starboard side being keyed.
Date: 01/23/2013
Views: 8271
|
|
|
dsc08627
The monowheel landing gear is in the up position and resting on the main wheel with some of the weight held by the block and tackle. This was taken just before putting on the braces to keep her from rolling. Been trying to get rid of that tv in the back
Date: 04/14/2012
Views: 11377
|
|
|
dsc08603
Since I'm going to have to remove the mono wheel I dont have much of an edge to close in the big hole in the bottom. I'll have a better look at it once its a tri-gear.
Date: 04/10/2012
Views: 11829
|
|
|
p1000470
p1000470.jpg
Date: 12/09/2011
Views: 11849
|
|
|
nex_2014_01_25_35
Dont judge me! You know you do it too. Anyways, was trying to see if my weight would cause the nose to come down. As you can see she likes being a tail dragger.
Date: 01/26/2014
Views: 10409
|
|
|
dsc09072
Here is a shot of the working angle. This was so much better than leaning over the edge. Kim's idea. Notice the heater behind Kim, this was key to keeping the temps even though the temps outside were in the 40's.
Date: 01/26/2013
Views: 9098
|
|
|
dsc09018
Started to make the axle jig. Used a simple setup of first taking large flat blocks of wood and caulking it to the floor somewhere over FS70. Then that allows me to fix the aluminum angle with a single screw once in its final position.
Date: 01/10/2013
Views: 10239
|
|
|
dsc08638
I used some thick good quality carpet to pad the ribs.
Date: 04/15/2012
Views: 8286
|
|
|
dsc08636
Here is Bill placing in some 2x6's to act as a support for the rear rib. The I-beam is 3 inches wide so the 2x6 fit perfectly. I'll explain later how those come into play.
Date: 04/15/2012
Views: 8175
|
|
|
20160403_160502.jpg
20160403_160502.jpg
Date: 04/03/2016
Views: 13450
|
|
|
dsc08611
Unused Mono wheel components. I'll probably be selling these soon.
Date: 04/10/2012
Views: 13749
|
|
|
p1000705
p1000705.jpg
Date: 03/12/2012
Views: 6178
|
|
|
dsc09036
Rib one port side again used around 112g of 420 cured at 78f for 12 hours.
Date: 01/23/2013
Views: 8838
|
|
|
p1000697
p1000697.jpg
Date: 03/12/2012
Views: 7036
|
|
|
dsc09056
Wetting out stbd side.
Date: 01/24/2013
Views: 8426
|
|
|
p1000715
p1000715.jpg
Date: 03/12/2012
Views: 6813
|
|