|
nex_2014_01_25_35
Dont judge me! You know you do it too. Anyways, was trying to see if my weight would cause the nose to come down. As you can see she likes being a tail dragger.
Date: 01/26/2014
Views: 8922
|
|
|
nex_2013_08_24_02
nex_2013_08_24_02.jpg
Date: 08/25/2013
Views: 6506
|
|
|
DSC08803
Me and my Uncle Kim.
Date: 06/10/2012
Views: 9999
|
|
|
dsc08641
Was going to use another plywood rib here but decided that the wide strap works fine. I later added some foam to the strap to give it some padding.
Date: 04/15/2012
Views: 7955
|
|
|
dsc08400
Very hard to work in the tunnel and I'm a small guy, 5'11“ 150#
Date: 03/25/2012
Views: 8837
|
|
|
dsc08661
Locating the center of the main gear hole. Used a pilot to be used to measure out the 10“ diameter on the bottom.
Date: 04/22/2012
Views: 11204
|
|
|
dsc09039
Port side done after cure.
Date: 01/23/2013
Views: 8011
|
|
|
p1000719
p1000719.jpg
Date: 03/12/2012
Views: 6262
|
|
|
p1000705
p1000705.jpg
Date: 03/12/2012
Views: 5798
|
|
|
dsc08964
Port side. Fitting of LG socket.
Date: 10/01/2012
Views: 8735
|
|
|
dsc08627
The monowheel landing gear is in the up position and resting on the main wheel with some of the weight held by the block and tackle. This was taken just before putting on the braces to keep her from rolling. Been trying to get rid of that tv in the back
Date: 04/14/2012
Views: 9600
|
|
|
dsc09019
Trash can is the best way to hold the landing gear legs.
Date: 01/10/2013
Views: 7682
|
|
|
nex_2014_01_25_31
Starboard side, need to trim the bolt.
Date: 01/26/2014
Views: 7585
|
|
|
dsc08399
Atempting to remove the mass ballance brace but to only find out later that it is bonded at the top.
Date: 03/25/2012
Views: 9066
|
|
|
Wanted to make a copy of B16 to make the cuts on before I cut the actual B16 part.
Wanted to make a copy of B16 to make the cuts on before I cut the actual B16 part.
Date: 04/03/2016
Views: 13603
|
|
|
dsc08640
OK not the best shot but here you can see I used the jack to move the rear rib in place under the airframe being careful not to pinch the belly. I then secured the rib in place but using some drywall screws in the 2x6. This way any weight will be transf
Date: 04/15/2012
Views: 7488
|
|
|
p1000636
p1000636.jpg
Date: 02/14/2012
Views: 5926
|
|
|
dsc09064
Bill does nice peel ply work!
Date: 01/24/2013
Views: 7741
|
|
|
p1000706
p1000706.jpg
Date: 03/12/2012
Views: 5836
|
|
|
dsc08618
Block and tackle used to hoist the front of the aircraft to aid in creating a jig. This hoist reduces the weight to 25%.
Date: 04/14/2012
Views: 13923
|
|