|
IMG_1369
Unfortunately I couldn't see that the drop shadow on the X was coming up with the release paper and it tore. CRAP!
Date: 05/18/2011
Views: 2914
|
|
|
IMG_1362ann
2010 11 12 Was a total waste of a day. After arriving at the hanger, I went in to open the hanger door. When the hanger door had been opened I was greeted by the sight of a drooping rear bumper on the Ranger. Went to the droopy side and found this. R
Date: 11/12/2010
Views: 4593
|
|
|
IMG_0135post
Date: 09/03/2010
Views: 2941
|
|
|
IMG_1477p
started on the nose wheel and strut. Made brackets for the wheel pant.
Date: 06/08/2011
Views: 3135
|
|
|
IMG_2681
2012 04 09 Well, after 4 weeks and buckets of DOT5 spent trying to make the Jaymar master cylinders work I have given up. They are just crap. So I'm taking the base of their base and building a new brake master setup using MATCO MC-4A master cylinders.
Date: 04/07/2012
Views: 3933
|
|
|
IMG_1425em
Just kind of a status photo as of 2010 12 20
Date: 12/20/2010
Views: 3363
|
|
|
IMG_1677
Still need adjustments on the parking brake wheel slot and brake lever slots.
Date: 04/29/2011
Views: 2613
|
|
|
IMG_3218
Once the brakes seemed to be OK it was time to run the engine and check it out. That didn't go well. Started well, warmed up with a bit of choke at the beginning. Smoothed out nicely and idled properly after it was all warmed up. Then I added throttle
Date: 05/18/2012
Views: 4841
|
|
|
IMG_1496p
Rudder
Date: 06/18/2011
Views: 2989
|
|
|
IMG_2755
New brake master cylinder set, installed and viewed from the tunnel. Brakes have been bled and seem to work well. Taxi testing will tell just how well they work.
Date: 04/24/2012
Views: 3658
|
|
|
IMG_3220
Similar staining and residual fuel on the port side as well.
Date: 05/18/2012
Views: 3362
|
|
|
IMG_1482p
Drilled starboard side bracket
Date: 06/08/2011
Views: 3098
|
|
|
IMG_1285ann
The tracing for the cover cut out.
Date: 03/30/2011
Views: 2711
|
|
|
IMG_1449p
Greatly simplified fuel plumbing, all cleaned up and tied down. Not a particularly good pic. I'll see if I can get a better one.
Date: 06/04/2011
Views: 2882
|
|
|
IMG_1236ann
Cut along the tape strip.
Date: 03/23/2011
Views: 3212
|
|
|
IMG_0112post
Date: 09/03/2010
Views: 3071
|
|
|
IMG_3290post
Here you can see where the gasket was cut by the bowl where it wasn't properly located.
Date: 05/31/2012
Views: 3921
|
|
|
IMG_1275ann
2011 03 29 Weather has turned cold again. No hanger work for a few days. Working in the shop on the wheel pants. The nose gear pant with mounting flange for the front piece
Date: 03/29/2011
Views: 3329
|
|
|
IMG_1668
Began fitting the brake fluid reservoir.
Date: 04/13/2011
Views: 3272
|
|
|
IMG_0127post
Date: 09/03/2010
Views: 2749
|
|