|
dsc08600
Thinking of modifying the mono wheel trailer as a jig to perform the tri-gear conversion.
Date: 04/10/2012
Views: 14650
|
|
|
E1
[quote="Bud Yerly"]"Make a glass cover that fits the hole out of three sheets of bid laid up on a flat surface. After cure, hold it up to the bottom of the plane and mark the contour. Cut and approximate the fit. It should be near level
Date: 10/05/2012
Views: 11993
|
|
|
dsc09070
While the layups are curing we stared work on the axles. Had to ream out the holes forMG02.
Date: 01/25/2013
Views: 9025
|
|
|
nex_2013_08_24_03
nex_2013_08_24_03.jpg
Date: 08/25/2013
Views: 7670
|
|
|
dsc08634
OK now that the plane is off the trailer and on its own wheel we were able to remove most of the trailer hardware and position the ribs. We also used the main bolts to hold the first rib in place. The other rib was left a little lower to be located once
Date: 04/15/2012
Views: 8501
|
|
|
dsc09063
Hey Bill!
Date: 01/24/2013
Views: 8862
|
|
|
p1000722
p1000722.jpg
Date: 03/12/2012
Views: 6901
|
|
|
dsc08967
Little clean up required on Port side.
Date: 10/01/2012
Views: 10512
|
|
|
p1000703
p1000703.jpg
Date: 03/12/2012
Views: 6128
|
|
|
dsc08627
The monowheel landing gear is in the up position and resting on the main wheel with some of the weight held by the block and tackle. This was taken just before putting on the braces to keep her from rolling. Been trying to get rid of that tv in the back
Date: 04/14/2012
Views: 11625
|
|
|
YouTube Channel
I've started a YouTube channel to vlog my build progress. Come check it out and leave a message!https://www.youtube.com/watch?v=OFgPUfHvLDE&list=PL2HSwhQop_QOThtzPUa_zLaMRj7qWyOv3
Date: 07/17/2021
Views: 247431
|
|
|
dsc08608
These will have to go. They are on top and I will remove them and put one vent on the bottom.
Date: 04/10/2012
Views: 13054
|
|
|
dsc09065
Stbd side peel ply removed.
Date: 01/25/2013
Views: 9425
|
|
|
dsc08960
Stb side after layups and peel ply removed.
Date: 10/01/2012
Views: 12387
|
|
|
p1000710
p1000710.jpg
Date: 03/12/2012
Views: 6384
|
|
|
dsc08612
Unused Mono wheel components. I'll probably be selling these soon.
Date: 04/10/2012
Views: 12558
|
|
|
DSC08796
Put in the panel to dream a little. Don't really know what I'm going to do. Was thinking of keeping it low cost for the first panel and keeping it analog until I can get the cash mula for something better like glass/IFR. Also want to fill the hole where
Date: 06/05/2012
Views: 12513
|
|
|
p1000714
p1000714.jpg
Date: 03/12/2012
Views: 6633
|
|
|
nex_2014_01_25_17
Rolled out on the grass. Notice the tail wheel is still there. I left it in due to not having the stacks of cash to hold the nose down.
Date: 01/26/2014
Views: 8401
|
|
|
dsc08628
Nic pic of the plane! If Bill would move his head out of the way! Notice I'm using a bungee cord to hold the doors open.
Date: 04/14/2012
Views: 9564
|
|