|
IMG_7382ann
The problem... The AN816 provided with the brake does not properly fit the threaded hole in the brake slave cylinder. It will screw in about two threads and that's all. You can see that the 90 degree hose end also sticks up in a big loop just waiting f
Date: 03/07/2010
Views: 4108
|
|
|
DSC04015_Large_post
Date: 10/19/2009
Views: 3766
|
|
|
IMG_0035
2010 07 06 - Wondered how the new brake would work on retraction. Set up for retraction testing. LG lever went to about 1/2" (1.275 cm) from the up lock and wouldn't go any further. Hitting something. Spent several hours trying to see what what
Date: 07/06/2010
Views: 3544
|
|
|
IMG_1217ann
Date: 06/13/2010
Views: 3367
|
|
|
IMG_7268post
Date: 02/21/2010
Views: 4038
|
|
|
IMG_0921post
After I put the aircraft back into the hanger, I loosened the master cylinder and rotated it about 30 degrees to the starboard. I'll see how that works tomorrow.
Date: 07/01/2010
Views: 3208
|
|
|
IMG_7530ann
First try was just to bolt the BSPP banjo onto the brake. Needless to say, that was just too simple to work. It wouldn't seat properly in the BSPT brake.
Date: 04/18/2010
Views: 3313
|
|
|
IMG_7539ann
Realizing that I'd need to do any remaining work at home, I removed the disk brake, gathered up the bits and headed for the shop. This is just a pic of the BSPT threaded hole in the disk brake. Had to clean it out as it was full of crap. Testing showed
Date: 04/18/2010
Views: 3157
|
|
|
IMG_1233ann
Went home and pulled a brake caliper off my Little Toot project. Brought it out to the hanger and the darn thing fits. So I have ordered a single puck version of the same brake caliper. When it arrives, it will go on and I'll replace the banjo hose end
Date: 06/21/2010
Views: 3179
|
|
|
IMG_7529ann
The new BSPP (British Standard Pipe Parallel) banjo bolts finally arrived from Speed Flow of Australia last week. Due to a death in the family and illnesses, I haven't gotten back to working on the Europa for several weeks. But I did today. I had also
Date: 04/18/2010
Views: 3174
|
|
|
IMG_0916post
Safety wired the bolts and check the installation. Pushed the aircraft and the brake stopped it. Held the brake and tried to push it aircraft. It wouldn't budge. Very good. Pulled it out of the hanger, started it up, let it warm properly and taxi tes
Date: 07/01/2010
Views: 5344
|
|
|
IMG_7441post
Here's a look at the tubing end of the two fittings. Again, similar, but not the same. Can't use the original fitting with the new tubing.
Date: 03/19/2010
Views: 3060
|
|
|
IMG_7383ann
The Issue, Continued... The blue Tee connector shown has a 3/8 NPT thread on the upper leg. it is a 3/8 x 24 National Pipe Thread. That is, it has a tapered thread. The thread measures 0.373 in on the narrow end and 0.408 in on the wide end. The othe
Date: 03/07/2010
Views: 3015
|
|
|
IMG_7540ann
That leaves two choices: #1 - tap the brake in BSPP threads or #2 - run the BSPT die over the bolt to thread in BSPT. The brake being aluminum and the bolt being stainless steel, I decided to go with #1 as it seemed easier.
Date: 04/18/2010
Views: 3104
|
|
|
IMG_7428post
My new banjo hose end for the brake arrived today. Good work Merlin Motor Sports.
Date: 03/15/2010
Views: 3011
|
|
|
IMG_0044post
So it's back to bleeding the brakes again. Pull the lines out so there's no high spots and there's an "all up" run to the master cylinder. Connect the bleed contraption and wait.
Date: 07/08/2010
Views: 3726
|
|
|
MDO_Aircraft_P2
Date: 10/18/2009
Views: 4076
|
|
|
Calliper 2
The best solution is shown in this pic from Mike Parkin. A Banjo fitting. The Banjo bolt is straight threads, it lies low, out of the way of grabby things and is stoutly attached. So, I have a number of bits on order from various suppliers in an attem
Date: 06/23/2009
Views: 3363
|
|
|
IMG_7269post
Date: 02/21/2010
Views: 3515
|
|
|
IMG_7267post
Date: 02/21/2010
Views: 3249
|
|