|
IMG_1446ann
Final brake plumbing and other stuff installed below the tunnel.
Date: 06/04/2011
Views: 2906
|
|
|
IMG_0248post
Date: 09/14/2010
Views: 3565
|
|
|
IMG_0110post
Date: 09/03/2010
Views: 2861
|
|
|
IMG_0101post
Date: 09/03/2010
Views: 2759
|
|
|
New MC-4A 07
Now we need mounting brackets. 1 1/4x1 1/4x1/8 aluminum angle has been cut to length (5 1/4 in) and is positioned on the brake mount for drilling the mounting holes using a wood block and clamp.
Date: 04/14/2012
Views: 3323
|
|
|
IMG_1319
Closeup of the hole for brake reservoir
Date: 04/15/2011
Views: 2886
|
|
|
IMG_1475p
Getting close to having wheel pants and gear leg fairings fitted
Date: 06/08/2011
Views: 3079
|
|
|
IMG_1412ann
2010 12 20 It's difficult to work in the hanger during the cold of late November and all of December. I tended to stay home and work in the shop on the "Taz" the Little Toot Sport Biplane I'm building. On the occasional nice day like this I ma
Date: 12/20/2010
Views: 3347
|
|
|
4_snaps
Old snap base installation with the new snap base.
Date: 06/23/2011
Views: 2881
|
|
|
IMG_1470ann
2011 01 26 January proves to be as cold and nasty as December. Finally have a day to work. Start by aligning the new outer flap brackets to make ready for mounting.
Date: 01/26/2011
Views: 2832
|
|
|
IMG_3367post
Request for fuel pressure input to the fuel pressure regulator. Installed a fuel pressure sensor on the input to the regulator. So now we have differential pressure out of the regulator and pressure into the regulator.
Date: 07/02/2012
Views: 4036
|
|
|
IMG_1244ann
The overall fit for the wheel pant is good. Need to make a hole and cutout to properly locate the wheel pant.
Date: 03/25/2011
Views: 2902
|
|
|
IMG_1374ann
I also received the new parts for the Rotax oil pressure regulator so I replaced them and safety wired it all back together.
Date: 11/17/2010
Views: 3336
|
|
|
IMG_1492p
Began reassembly of the control surfaces. Starboard wing aileron.
Date: 06/18/2011
Views: 2760
|
|
|
IMG_1227ann
This is where the flap switch will reside.
Date: 03/18/2011
Views: 2920
|
|
|
IMG_2604
Got out the inspection mirror and made sure the gasket was in place all the way round the bowl. It was.
Date: 05/30/2012
Views: 5206
|
|
|
IMG_0025post
Date: 08/30/2010
Views: 4341
|
|
|
IMG_1503ann
Made up a template for cover for the console. It has been pretty chewed up with removal of some stuff and installation of new stuff.
Date: 02/18/2011
Views: 2952
|
|
|
IMG_2683
Here are the new MATCO master cylinders connected to the old levers sitting on the old base. Now how do we contain the back ends to make this work?
Date: 04/07/2012
Views: 3043
|
|
|
IMG_1485s
Other side
Date: 06/10/2011
Views: 2965
|
|