|
IMG_0916post
Safety wired the bolts and check the installation. Pushed the aircraft and the brake stopped it. Held the brake and tried to push it aircraft. It wouldn't budge. Very good. Pulled it out of the hanger, started it up, let it warm properly and taxi tes
Date: 07/01/2010
Views: 5239
|
|
|
IMG_1218ann
Date: 06/13/2010
Views: 3541
|
|
|
IMG_0044post
So it's back to bleeding the brakes again. Pull the lines out so there's no high spots and there's an "all up" run to the master cylinder. Connect the bleed contraption and wait.
Date: 07/08/2010
Views: 3639
|
|
|
IMG_9536ann
Date: 06/03/2010
Views: 3204
|
|
|
IMG_7428post
My new banjo hose end for the brake arrived today. Good work Merlin Motor Sports.
Date: 03/15/2010
Views: 2953
|
|
|
DSC04012_Large_post
Date: 10/19/2009
Views: 4058
|
|
|
IMG_0912post
After much flailing about which shall not be documented here, I went back to the double puck brake and spent a couple days trying to bleed the new system. Without much luck. I called Robby at Grove Aircraft and he pointed out that if there were any high
Date: 07/01/2010
Views: 3485
|
|
|
IMG_7269post
Date: 02/21/2010
Views: 3453
|
|
|
IMG_1216ann
Date: 06/13/2010
Views: 3404
|
|
|
IMG_7543ann
The final result. The banjo hose end bolts nicely to the brake. With any luck, I'll take the brake back to the airport after work tomorrow and reinstall it all and see if I can bleed the brakes.
Date: 04/18/2010
Views: 3490
|
|
|
IMG_7440post
2010 03 19 - Checked to see if the new brake banjo hardware would work while completing the Annual Condition Inspection on the Europa. This is a comparison of the original fitting from the brake with the new banjo bolt that's supposed to work. Close, bu
Date: 03/19/2010
Views: 3290
|
|
|
Calliper 2
The best solution is shown in this pic from Mike Parkin. A Banjo fitting. The Banjo bolt is straight threads, it lies low, out of the way of grabby things and is stoutly attached. So, I have a number of bits on order from various suppliers in an attem
Date: 06/23/2009
Views: 3277
|
|
|
IMG_7270post
Date: 02/21/2010
Views: 3782
|
|
|
IMG_0042post
2010 07 08 - Back to the airport and back under the aircraft. With more aggressive abrasives, I was able to relieve the rub just a bit more. Not much at all, as you can see from the picture.
Date: 07/08/2010
Views: 4150
|
|
|
IMG_0035
2010 07 06 - Wondered how the new brake would work on retraction. Set up for retraction testing. LG lever went to about 1/2" (1.275 cm) from the up lock and wouldn't go any further. Hitting something. Spent several hours trying to see what what
Date: 07/06/2010
Views: 3436
|
|
|
MDO_Aircraft_P2
Date: 10/18/2009
Views: 3948
|
|
|
IMG_0036
2010 07 07 - Back to retraction tests. Thought that the fixtures sticking up off the caliper might be a problem. Replaced them with the 90 degree fitting and a straight hose end. Much neater and more compact, but I'll have to bleed the brakes again whe
Date: 07/07/2010
Views: 3800
|
|
|
IMG_7382ann
The problem... The AN816 provided with the brake does not properly fit the threaded hole in the brake slave cylinder. It will screw in about two threads and that's all. You can see that the 90 degree hose end also sticks up in a big loop just waiting f
Date: 03/07/2010
Views: 4010
|
|
|
IMG_1223ann
2010 06 21 - What's this, the 4th or 5th try at getting a seal on the banjo to the brake caliper? Still leaks.
Date: 06/21/2010
Views: 3353
|
|
|
IMG_1167ann
Went to the hanger after work and put the brake back together. Seems to work fine. I have not safety wired it yet as I want to add fluid, bleed and give it a good test beforehand. When all tests wel,l with no leaks, I'll wire it up. Could have used a
Date: 04/19/2010
Views: 3167
|
|