|
dsc09073
Rib 2 template.
Date: 01/26/2013
Views: 9385
|
|
|
dsc09064
Bill does nice peel ply work!
Date: 01/24/2013
Views: 9136
|
|
|
dsc09070
While the layups are curing we stared work on the axles. Had to ream out the holes forMG02.
Date: 01/25/2013
Views: 9193
|
|
|
photo
No pictures of the progress of putting in the LG layups on the port side. Here I am putting down the peel ply.
Date: 08/20/2012
Views: 15904
|
|
|
nex_2014_01_25_01
Starboard side after Uni over ribs 3 and 4. Added Bid on the X to reinforce the cuts needed to get the Uni to lay flat. Also filled in Rib 1 air buble.
Date: 01/25/2014
Views: 8135
|
|
|
20141102_161049
20141102_161049.jpg
Date: 11/02/2014
Views: 15847
|
|
|
photo (2)
Small area to work in. Back was killing me after that job. can't wait to give my back the same treatment when doing the ribs and starboard side.
Date: 08/20/2012
Views: 14184
|
|
|
nex_2014_01_25_07
What a mess.
Date: 01/25/2014
Views: 8411
|
|
|
dsc08966
Port side LG socket hole.
Date: 10/01/2012
Views: 11517
|
|
|
20141102_161000
template for new firewall.
Date: 11/02/2014
Views: 17629
|
|
|
nex_2013_08_24_03
nex_2013_08_24_03.jpg
Date: 08/25/2013
Views: 7833
|
|
|
dsc08628
Nic pic of the plane! If Bill would move his head out of the way! Notice I'm using a bungee cord to hold the doors open.
Date: 04/14/2012
Views: 9729
|
|
|
dsc08627
The monowheel landing gear is in the up position and resting on the main wheel with some of the weight held by the block and tackle. This was taken just before putting on the braces to keep her from rolling. Been trying to get rid of that tv in the back
Date: 04/14/2012
Views: 11793
|
|
|
nex_2014_01_12_06
She's got a leg!
Date: 01/13/2014
Views: 8051
|
|
|
nex_2014_01_12_01
Bolt hole for LG port side filed to size.
Date: 01/13/2014
Views: 7960
|
|
|
dsc08629
In a few mins she will no longer be a monowheel :-(
Date: 04/14/2012
Views: 9165
|
|
|
dsc08638
I used some thick good quality carpet to pad the ribs.
Date: 04/15/2012
Views: 8585
|
|
|
dsc08662
The 10“ diameter from the pilot hole.
Date: 04/22/2012
Views: 13395
|
|
|
dsc08634
OK now that the plane is off the trailer and on its own wheel we were able to remove most of the trailer hardware and position the ribs. We also used the main bolts to hold the first rib in place. The other rib was left a little lower to be located once
Date: 04/15/2012
Views: 8677
|
|
|
dsc08636
Here is Bill placing in some 2x6's to act as a support for the rear rib. The I-beam is 3 inches wide so the 2x6 fit perfectly. I'll explain later how those come into play.
Date: 04/15/2012
Views: 8504
|
|