|
IMG_0107post
Date: 09/03/2010
Views: 2616
|
|
|
IMG_0033post
Date: 09/01/2010
Views: 3462
|
|
|
IMG_0457ann
2010 10 20 While in Florida, I had Bud go over the aircraft to see what issues he could find. One issue was the lack of spar pin reinforcements when the cockpit module was built.
Date: 10/20/2010
Views: 3100
|
|
|
IMG_1319
Closeup of the hole for brake reservoir
Date: 04/15/2011
Views: 2886
|
|
|
IMG_0824ann
Somewhere along the way, a couple spacers had been lost. Made up new ones. Also put anchor nuts on the radiator mounting flanges to make assembly easier, sorta, kinda. Seems like reassembling this aircraft is more difficult than the original building.
Date: 01/27/2011
Views: 3305
|
|
|
IMG_1371ann
2010 11 17 Had some leftover SuperFil from wing work so I cleaned up the holes in the tail where the old tailwheel cables exited the aft fuselage and proceeded to fill them.
Date: 11/17/2010
Views: 3040
|
|
|
IMG_3538em
I removed the entire airbox to to check all the plumbing connections.
Date: 07/30/2012
Views: 5688
|
|
|
IMG_0092post
Date: 09/03/2010
Views: 2986
|
|
|
IMG_1303
Fitting the wheel pants. Here, I'm using a mirror to see where the tire rubs on the opening so I can mark areas to relieve.
Date: 04/14/2011
Views: 2535
|
|
|
Wings on 1
Tommy and Russ stopped by to help me put the wings back on.
Date: 07/01/2011
Views: 3222
|
|
|
IMG_2706
Assembled everything. You can see the spacers fit to hold the master cylinders in alignment. Plumbing in place. The unit is about 1 1/2 in. taller than the old Jaymar. I'm wondering if it will fit or will I have to lower it in the mount? We'll see to
Date: 04/11/2012
Views: 3876
|
|
|
IMG_1275ann
2011 03 29 Weather has turned cold again. No hanger work for a few days. Working in the shop on the wheel pants. The nose gear pant with mounting flange for the front piece
Date: 03/29/2011
Views: 3230
|
|
|
IMG_0188post
Date: 09/08/2010
Views: 2766
|
|
|
IMG_1479p
Put the nose gear pant on and drilled holes through the brackets
Date: 06/08/2011
Views: 3067
|
|
|
IMG_0927ann
And fill/sand continues on the wing repair areas.
Date: 03/02/2011
Views: 2659
|
|
|
IMG_2681
2012 04 09 Well, after 4 weeks and buckets of DOT5 spent trying to make the Jaymar master cylinders work I have given up. They are just crap. So I'm taking the base of their base and building a new brake master setup using MATCO MC-4A master cylinders.
Date: 04/07/2012
Views: 3671
|
|
|
2_Door_Knobs
Nice low profile head
Date: 06/23/2011
Views: 3199
|
|
|
IMG_0247post
Date: 09/13/2010
Views: 2504
|
|
|
IMG_1285ann
The tracing for the cover cut out.
Date: 03/30/2011
Views: 2554
|
|
|
IMG_1589ann
I need to get two brake lines and a reservoir line in there and attached somehow.
Date: 03/15/2011
Views: 3270
|
|