|
nex_2014_01_12_05
Port side top.
Date: 01/13/2014
Views: 8054
|
|
|
dsc08629
In a few mins she will no longer be a monowheel :-(
Date: 04/14/2012
Views: 9097
|
|
|
dsc08630
Though this was a neat pic of the mono wheel in the retracted position.
Date: 04/14/2012
Views: 8183
|
|
|
20141102_154450
Gear cover removed, now for removing the throttle box. This is all prep work to patch up the mono wheel hole.
Date: 11/02/2014
Views: 18621
|
|
|
p1000469
p1000469.jpg
Date: 12/09/2011
Views: 11191
|
|
|
nex_2013_08_24_03
nex_2013_08_24_03.jpg
Date: 08/25/2013
Views: 7765
|
|
|
dsc09066
Port side peel ply removed. Oh notice the caps in the sockets. What I did was take a block of foam and push it down in the socket, then took it back out and covered it with car wax. Once all the ribs are in I'll see how it worked.
Date: 01/25/2013
Views: 9424
|
|
|
DSC08797
Port side
Date: 06/05/2012
Views: 10527
|
|
|
p1000706
p1000706.jpg
Date: 03/12/2012
Views: 6190
|
|
|
dsc08631
More of the same.
Date: 04/14/2012
Views: 8079
|
|
|
p1000693
p1000693.jpg
Date: 03/12/2012
Views: 6775
|
|
|
dsc08642
From the start the airframe was sitting 2.5 deg tail low and 0.1 deg to port. Not bad for just putting her on there. I jacked up the back of the trailer to get it as near to 0.0 as possible and also shifted the airframe latterly to turn that .1 to 0.0 a
Date: 04/15/2012
Views: 12201
|
|
|
dsc08640
OK not the best shot but here you can see I used the jack to move the rear rib in place under the airframe being careful not to pinch the belly. I then secured the rib in place but using some drywall screws in the 2x6. This way any weight will be transf
Date: 04/15/2012
Views: 9074
|
|
|
dsc09030
Starboard side done.
Date: 01/22/2013
Views: 9351
|
|
|
DSC08796
Put in the panel to dream a little. Don't really know what I'm going to do. Was thinking of keeping it low cost for the first panel and keeping it analog until I can get the cash mula for something better like glass/IFR. Also want to fill the hole where
Date: 06/05/2012
Views: 12532
|
|
|
dsc09070
While the layups are curing we stared work on the axles. Had to ream out the holes forMG02.
Date: 01/25/2013
Views: 9121
|
|
|
dsc09034
Starboard side done. Pic taken before a little clean up.
Date: 01/22/2013
Views: 8450
|
|
|
nex_2014_01_25_06
Mains on the ground for the first time.
Date: 01/25/2014
Views: 8180
|
|
|
p1000617
p1000617.jpg
Date: 01/29/2012
Views: 10067
|
|
|
DSC08800
starboard side
Date: 06/05/2012
Views: 10441
|
|