|
EuropaCheckListFront
Date: 12/06/2008
Views: 3678
|
|
|
Intercooler04
Date: 01/07/2006
Views: 4067
|
|
|
IMG_2854
Date: 12/03/2008
Views: 3327
|
|
|
IMG_9534ann
Date: 06/03/2010
Views: 3143
|
|
|
DSCN4667small
Date: 08/27/2006
Views: 3828
|
|
|
IMG_1167ann
Went to the hanger after work and put the brake back together. Seems to work fine. I have not safety wired it yet as I want to add fluid, bleed and give it a good test beforehand. When all tests wel,l with no leaks, I'll wire it up. Could have used a
Date: 04/19/2010
Views: 3179
|
|
|
IMG_7440post
2010 03 19 - Checked to see if the new brake banjo hardware would work while completing the Annual Condition Inspection on the Europa. This is a comparison of the original fitting from the brake with the new banjo bolt that's supposed to work. Close, bu
Date: 03/19/2010
Views: 3305
|
|
|
IMG_7541ann
It took almost an hour to carefully and safely get the tap started in the aluminum brake. I sure didn't want to screw that up. Once I had a good start and the tap began to cut, I clamped the tap in the vice with the brake held high so chips fall out and
Date: 04/18/2010
Views: 3029
|
|
|
1_snaps
The snap bases for the seat back cushions were poorly installed by my interior guy. Just a skinny screw through the over-sized hole the snap base where the original rivet went.
Date: 06/23/2011
Views: 4607
|
|
|
DSCN6089Ann
Date: 06/12/2007
Views: 3668
|
|
|
IMG_6972post
Pointing out areas relieved for fit over swing arm
Date: 12/27/2009
Views: 3080
|
|
|
IMG_7383ann
The Issue, Continued... The blue Tee connector shown has a 3/8 NPT thread on the upper leg. it is a 3/8 x 24 National Pipe Thread. That is, it has a tapered thread. The thread measures 0.373 in on the narrow end and 0.408 in on the wide end. The othe
Date: 03/07/2010
Views: 2964
|
|
|
IMG_6975post
Overall length of ramp
Date: 12/27/2009
Views: 3463
|
|
|
LongRangeTankPort
Date: 07/31/2004
Views: 4061
|
|
|
IntercoolerFig1
Date: 01/07/2006
Views: 4175
|
|
|
IMG_7384ann
The threads on both fittings are 24/in. So that's a match. The issue is one is straight and the other pipe thread.
Date: 03/07/2010
Views: 3132
|
|
|
DSC04015_Large_post
Date: 10/19/2009
Views: 3686
|
|
|
IMG_0888post
This is the Grove brake caliper I am using. It may not be the perfect replacement for the Europa brake but it sure works. I've e-mailed Robby at Grove and asked if he'd like me to send the old Europa brake caliper to see if they have a better replacemen
Date: 06/29/2010
Views: 3147
|
|
|
IMG_1237ann
The new regulator is 25 psi. Should be plenty of pressure available to feed the 914.
Date: 06/21/2010
Views: 3558
|
|
|
IMG_6687Ann
Date: 02/15/2008
Views: 4340
|
|