|
IMG_6688Ann
Date: 02/15/2008
Views: 3657
|
|
|
DSCN6098Ann
Date: 06/13/2007
Views: 3406
|
|
|
IMG_9571post
The fuel lines were tied with tie-wraps and 1/2" (12.7 mm) rubber fuel hose lengths. The vent hose was tied in as well by running it through short lengths of fuel hose and using tie-wraps to hold the rubber hose and protect the vent line from chafin
Date: 06/12/2010
Views: 4396
|
|
|
IMG_0912post
After much flailing about which shall not be documented here, I went back to the double puck brake and spent a couple days trying to bleed the new system. Without much luck. I called Robby at Grove Aircraft and he pointed out that if there were any high
Date: 07/01/2010
Views: 3588
|
|
|
InsideOpen
Date: 07/09/2003
Views: 4895
|
|
|
Plexi02small
Date: 04/04/2005
Views: 5415
|
|
|
5_snaps
The new snap bases installed in the head rest.
Date: 06/23/2011
Views: 4570
|
|
|
IMG_9561ann
Overview. Flip the fuel pressure regulator, add firesleeve and put in the AN6-6 nipple to connect the input hose to the input fuel flow meter and the installation will be complete. Maybe later this week when all the bits for the brake and fuel line come
Date: 06/06/2010
Views: 3673
|
|
|
IMG_1093ann
Finally, problem #3 - 3/8" hose barb input and 1/4" hose barb output. There is an issue locating a 1/4" hose barb banjo to attach to the Rotax fuel pressure regulator.
Date: 04/03/2010
Views: 3876
|
|
|
3_Door_Knobs
Similarly, the screw portion is nice and flat so it won't hang up on the aluminum guard plate when pressed closed.
Date: 06/23/2011
Views: 5089
|
|
|
IMG_9572post
Made sure that the vent line was attached and run to the back and down into the area below the engine, but not into the air stream.
Date: 06/12/2010
Views: 3831
|
|
|
IMG_6680Ann
Date: 02/15/2008
Views: 3664
|
|
|
IMG_6783small
Date: 02/23/2008
Views: 3345
|
|
|
DSCN6116Ann
Date: 06/14/2007
Views: 3261
|
|
|
IMG_6972post
Pointing out areas relieved for fit over swing arm
Date: 12/27/2009
Views: 3186
|
|
|
DSCN6091Ann
Date: 06/12/2007
Views: 3548
|
|
|
IMG_7383ann
The Issue, Continued... The blue Tee connector shown has a 3/8 NPT thread on the upper leg. it is a 3/8 x 24 National Pipe Thread. That is, it has a tapered thread. The thread measures 0.373 in on the narrow end and 0.408 in on the wide end. The othe
Date: 03/07/2010
Views: 3007
|
|
|
Plexi01small
Date: 04/04/2005
Views: 3341
|
|
|
IMG_6788small
Date: 02/23/2008
Views: 3669
|
|
|
IMG_0041post
But it was enough to allow the LG to retract fully. Ran the gear up and down about a dozen times. Works great.
Date: 07/08/2010
Views: 4414
|
|