|
p1000693
p1000693.jpg
Date: 03/12/2012
Views: 6371
|
|
|
p1000688
p1000688.jpg
Date: 03/12/2012
Views: 6344
|
|
|
p1000630
p1000630.jpg
Date: 02/14/2012
Views: 6976
|
|
|
nex_2013_08_24_04
As you see here the port side is done with rib 3 and 4. I didn't have photos of doing the layups.
Date: 08/25/2013
Views: 6708
|
|
|
DSC08796
Put in the panel to dream a little. Don't really know what I'm going to do. Was thinking of keeping it low cost for the first panel and keeping it analog until I can get the cash mula for something better like glass/IFR. Also want to fill the hole where
Date: 06/05/2012
Views: 11296
|
|
|
dsc08607
Starting to prep the bays for the tri-gear conversion.
Date: 04/10/2012
Views: 8940
|
|
|
nex_2014_01_25_04
Bill helping hoist the aircraft up to remove the jig.
Date: 01/25/2014
Views: 6938
|
|
|
photo (2)
Small area to work in. Back was killing me after that job. can't wait to give my back the same treatment when doing the ribs and starboard side.
Date: 08/20/2012
Views: 12680
|
|
|
dsc08964
Port side. Fitting of LG socket.
Date: 10/01/2012
Views: 8709
|
|
|
p1000698
p1000698.jpg
Date: 03/12/2012
Views: 6673
|
|
|
dsc08614
Anybody know a easy way to remove this rust?
Date: 04/10/2012
Views: 9395
|
|
|
nex_2014_01_25_01
Starboard side after Uni over ribs 3 and 4. Added Bid on the X to reinforce the cuts needed to get the Uni to lay flat. Also filled in Rib 1 air buble.
Date: 01/25/2014
Views: 6635
|
|
|
dsc08605
When I received the plane it had a few areas of this green tape. I guess it was going to be used as a release agent for some sort of jig fabrication. I have found that this 3M stuff works very well.
Date: 04/10/2012
Views: 11166
|
|
|
dsc09035
Rib one after cure of 420 and peel ply removed. Think we used 112g of 420 here due to the odd angle.
Date: 01/23/2013
Views: 7172
|
|
|
dsc09074
Port side Rib 2 layup.
Date: 01/26/2013
Views: 8354
|
|
|
dsc09033
Port side done.
Date: 01/22/2013
Views: 7407
|
|
|
dsc09073
Rib 2 template.
Date: 01/26/2013
Views: 7972
|
|
|
YouTube Channel
I've started a YouTube channel to vlog my build progress. Come check it out and leave a message!https://www.youtube.com/watch?v=OFgPUfHvLDE&list=PL2HSwhQop_QOThtzPUa_zLaMRj7qWyOv3
Date: 07/17/2021
Views: 241756
|
|
|
p1000469
p1000469.jpg
Date: 12/09/2011
Views: 10293
|
|
|
Wanted to make a copy of B16 to make the cuts on before I cut the actual B16 part.
Wanted to make a copy of B16 to make the cuts on before I cut the actual B16 part.
Date: 04/03/2016
Views: 13564
|
|