|
Close up of the relief cut.
Close up of the relief cut.
Date: 04/03/2016
Views: 13513
|
|
|
p1000724
p1000724.jpg
Date: 03/12/2012
Views: 7325
|
|
|
dsc09072
Here is a shot of the working angle. This was so much better than leaning over the edge. Kim's idea. Notice the heater behind Kim, this was key to keeping the temps even though the temps outside were in the 40's.
Date: 01/26/2013
Views: 8197
|
|
|
p1000704
p1000704.jpg
Date: 03/12/2012
Views: 5979
|
|
|
dsc09041
Port side guides being placed for layup.
Date: 01/23/2013
Views: 8356
|
|
|
20141102_154504
Cut old fuel lines. Gona have to replace them anyways. Now I just need to remove the stop block where the gear handle went.
Date: 11/02/2014
Views: 16316
|
|
|
p1000715
p1000715.jpg
Date: 03/12/2012
Views: 6600
|
|
|
dsc08963
Port side. LG socket fitting.
Date: 10/01/2012
Views: 9349
|
|
|
Orange part created in turbocad and printed on a 3D printer from ABS. Printer is a Prusa i3 X, cost is around $300.
Orange part created in turbocad and printed on a 3D printer from ABS. Printer is a Prusa i3 X, cost is around $300.
Date: 04/03/2016
Views: 18787
|
|
|
nex_2013_08_24_04
As you see here the port side is done with rib 3 and 4. I didn't have photos of doing the layups.
Date: 08/25/2013
Views: 7021
|
|
|
dsc08640
OK not the best shot but here you can see I used the jack to move the rear rib in place under the airframe being careful not to pinch the belly. I then secured the rib in place but using some drywall screws in the 2x6. This way any weight will be transf
Date: 04/15/2012
Views: 7884
|
|
|
DSC08800
starboard side
Date: 06/05/2012
Views: 9412
|
|
|
dsc09018
Started to make the axle jig. Used a simple setup of first taking large flat blocks of wood and caulking it to the floor somewhere over FS70. Then that allows me to fix the aluminum angle with a single screw once in its final position.
Date: 01/10/2013
Views: 9291
|
|
|
dsc09060
Wetting out stbd side.
Date: 01/24/2013
Views: 8073
|
|
|
YouTube Channel
I've started a YouTube channel to vlog my build progress. Come check it out and leave a message!https://www.youtube.com/watch?v=OFgPUfHvLDE&list=PL2HSwhQop_QOThtzPUa_zLaMRj7qWyOv3
Date: 07/17/2021
Views: 244280
|
|
|
p1000698
p1000698.jpg
Date: 03/12/2012
Views: 6869
|
|
|
dsc09065
Stbd side peel ply removed.
Date: 01/25/2013
Views: 8472
|
|
|
p1000628
p1000628.jpg
Date: 02/14/2012
Views: 7562
|
|
|
dsc08618
Block and tackle used to hoist the front of the aircraft to aid in creating a jig. This hoist reduces the weight to 25%.
Date: 04/14/2012
Views: 14876
|
|
|
dsc09074
Port side Rib 2 layup.
Date: 01/26/2013
Views: 8688
|
|