|
New MC-4A 07
Now we need mounting brackets. 1 1/4x1 1/4x1/8 aluminum angle has been cut to length (5 1/4 in) and is positioned on the brake mount for drilling the mounting holes using a wood block and clamp.
Date: 04/14/2012
Views: 3399
|
|
|
IMG_0149post
Date: 09/04/2010
Views: 2953
|
|
|
IMG_0022post
Date: 08/30/2010
Views: 4988
|
|
|
Wings on 1
Tommy and Russ stopped by to help me put the wings back on.
Date: 07/01/2011
Views: 3333
|
|
|
IMG_1461p
Starboard wing outer flap bracket
Date: 06/05/2011
Views: 3289
|
|
|
IMG_0002post
Date: 08/26/2010
Views: 5839
Keywords:
|
|
|
IMG_1475p
Getting close to having wheel pants and gear leg fairings fitted
Date: 06/08/2011
Views: 3175
|
|
|
IMG_1306
Continue fitting wheel pants, gear leg fairings and the console cover.
Date: 04/15/2011
Views: 3129
|
|
|
1_snaps
The headrest snap bases for the seat back tabs were never done well by my upholstery guy. Just a skinny screw through the hole where a big rivet had been removed. And simple nuts on the underside.
Date: 06/23/2011
Views: 3072
|
|
|
IMG_3334post
Requests to check the fuel delivery system. Started with the gascolator. Any large quantity of crap in the gascolator? Here's the fuel from the gascolator in the test vessel. A tiny bit of black crud from who knows what. But not enough to cause a pro
Date: 06/13/2012
Views: 4097
|
|
|
IMG_0221post
Date: 09/10/2010
Views: 2805
|
|
|
IMG_0162post
Date: 09/05/2010
Views: 2806
|
|
|
IMG_1587ann
2011 03 13 Looking to see how all the brake lines will fit.
Date: 03/15/2011
Views: 2867
|
|
|
IMG_1345ann
Used a big AN970 washer with an elastic stop nut to hold it all in place.
Date: 11/05/2010
Views: 3070
|
|
|
IMG_2604
Got out the inspection mirror and made sure the gasket was in place all the way round the bowl. It was.
Date: 05/30/2012
Views: 5314
|
|
|
IMG_0190post
Date: 09/08/2010
Views: 3014
|
|
|
IMG_2685
I elected to make up a support structure from some 12" 1 1/2 x 1 1/2 wide aluminum angle i had in my aluminum bin. Cut two lengths 5 1/2" long and clamped them to the base well centered and drilled out holes matching the base. Attached them t
Date: 04/09/2012
Views: 3154
|
|
|
IMG_3301post
The issue being the softness and flexibility of the gasket material. Makes it difficult to ensure proper location while reattaching the bowl. The gasket is probably fine for a carb rebuild where you are doing it on the bench and can turn the carb over f
Date: 06/01/2012
Views: 4172
|
|
|
IMG_1460p
Starboard wing tip
Date: 06/05/2011
Views: 3324
|
|
|
IMG_1272ann
The nose wheel pant has been cut and prepared to receive inside layups to create a mounting flange.
Date: 03/28/2011
Views: 2748
|
|