|
|
IMG_1469p
Cleaned up the tunnel area.
Date: 06/05/2011
Views: 4754
|
|
|
IMG_1465p
Received the second replacement X. This one was correct and applied.
Date: 06/05/2011
Views: 4698
|
|
|
|
IMG_1446ann
Final brake plumbing and other stuff installed below the tunnel.
Date: 06/04/2011
Views: 4641
|
|
|
IMG_1449p
Greatly simplified fuel plumbing, all cleaned up and tied down. Not a particularly good pic. I'll see if I can get a better one.
Date: 06/04/2011
Views: 4450
|
|
|
|
IMG_1444p
Completed the brake plumbing, filling and bleeding. Cockpit pretty much back together.
Date: 06/04/2011
Views: 4415
|
|
|
IMG_1420
Port aft fuselage where the tailwheel cables used to exit.
Date: 05/31/2011
Views: 6115
|
|
|
|
IMG_1422
Brake plumbing pretty well done. Working on the brake bleed.
Date: 05/31/2011
Views: 6027
|
|
|
IMG_1416
End of May. Applied primer to all the repaired and patched areas. Port wing outboard flap bracket area.
Date: 05/31/2011
Views: 6558
|
|
|
|
IMG_1417
Starboard wing tip
Date: 05/31/2011
Views: 5234
|
|
|
IMG_1418
Starboard wing outboard flap bracket area
Date: 05/31/2011
Views: 5127
|
|
|
|
IMG_1419
Starboard aft fuselage where the tailwheel cables used to exit.
Date: 05/31/2011
Views: 5007
|
|
|
IMG_1412
Another issue with the pre-built cockpit module. The fuel tank was not supported on the aluminum angle. Bud suggested this could cause tank cracking and recommended some sort of support be added. I cut a wedge from a length of balsa and covered it with
Date: 05/28/2011
Views: 6121
|
|
|
|
IMG_1415
Bonding the aluminum angle bracket for the brake reservoir with Araldite
Date: 05/28/2011
Views: 6037
|
|
|
IMG_1415
Continuing work on the brake plumbing. And the usual wheel pants and gear leg fairing work.
Date: 05/28/2011
Views: 6051
|
|
|
|
IMG_1402
Received the replacement X for the Reg. No. Unfortunately, they made up the wrong X. Note the drop shadow. Order another one...
Date: 05/27/2011
Views: 4837
|
|
|
IMG_1405
Put the stabs back on and check them out and checked out the trim for operation. All OK.
Date: 05/27/2011
Views: 6188
|
|
|
|
IMG_1408
Still working on the brake plumbing. The translucent nylon was not fitting properly. Going back to the black stuff.
Date: 05/27/2011
Views: 6254
|
|
|
IMG_1410
Sanded down the filler on the scuffed wing tip.
Date: 05/27/2011
Views: 7087
|
|
|
|
IMG_1396
Had to shorten the new intercooler hose to allow everything to move to port. Repositioned the aluminum baffle and the intercooler and all fits now.
Date: 05/26/2011
Views: 5099
|
|
|
IMG_1400
Noticed that the underside of the starboard wing tip was scuffed. Applied filler to begin to clean it up. As well as continuing to work on pants and fairings.
Date: 05/26/2011
Views: 6018
|
|
