| 
 | 
 
DSC00153
 
Lathe installed
 
Date: 09/01/2015
 
Views: 36621
 
 
 | 
 | 
 | 
 
DSC00149
 
Winch installed in garage
 
Date: 09/01/2015
 
Views: 31662
 
 
 | 
 | 
| 
 | 
 
IMG_0344[1]
 
Aircraft parts & Documents stored
 
Date: 09/04/2014
 
Views: 26454
 
 
 | 
 | 
 | 
 
IMG_0340[1]
 
cloth cabinet installed.
 
Date: 09/04/2014
 
Views: 45191
 
 
 | 
 | 
| 
 | 
 
IMG_0187[1]
 
Started to fit fixtures and fittings
 
Date: 04/13/2014
 
Views: 43446
 
 
 | 
 | 
 | 
 
IMG_0189[1]
 
Date: 04/13/2014
 
Views: 43255
 
 
 | 
 | 
| 
 | 
 
IMG_0190[1]
 
Date: 04/13/2014
 
Views: 40845
 
 
 | 
 | 
 | 
 
IMG_0191[1]
 
Date: 09/12/2015
 
Views: 30920
 
 
 | 
 | 
| 
 | 
 
DSC00229
 
Still some work to do but happy so far.
 
Date: 09/10/2015
 
Views: 91890
 
 
 | 
 | 
 | 
 
DSC00228
 
Had to remove more of the rudder than I wanted so build up rudder trailing edge by attaching peel ply to the outside of the rudder and build up trailing edge using flox around the edge and an initial 2 ply of bid. i'll apply an additional 2 ply after the 
 
Date: 09/10/2015
 
Views: 66051
 
 
 | 
 | 
| 
 | 
 
DSC00219
 
bracket installed
 
Date: 09/09/2015
 
Views: 77634
 
 
 | 
 | 
 | 
 
DSC00214
 
blue foam placed in rudder to fill void
 
Date: 09/08/2015
 
Views: 76618
 
 
 | 
 | 
| 
 | 
 
DSC00215
 
foam removed to make space for the rudder bracket
 
Date: 09/09/2015
 
Views: 75687
 
 
 | 
 | 
 | 
 
DSC00212
 
Marking position for bracket on rear bulk head
 
Date: 09/08/2015
 
Views: 92236
 
 
 | 
 | 
| 
 | 
 
IMG_0823
 
Same of port side.
 
Date: 09/03/2015
 
Views: 24108
 
 
 | 
 | 
 | 
 
Torque tube
 
Took some measurements and sent query to Europa. Response was I required the issue 1 TP38s
 
Date: 09/03/2015
 
Views: 18779
 
 
 | 
 | 
| 
 | 
 
DSC00155
 
As you can see the Issue 1 Bearings are considerably longer and will require shortening once I have the correct dimensions.
 
Date: 09/03/2015
 
Views: 29594
 
 
 | 
 | 
 | 
 
IMG_0821
 
Trial fitted the torque tube but it looks like the TP38 bearing is too short!
 
Date: 09/03/2015
 
Views: 27694
 
 
 | 
 | 
| 
 | 
 
DSC00165
 
Trial fit of the push rod bracket! Doesn't look good. This is going to take some thought.
 
Date: 09/04/2015
 
Views: 94517
 
 
 | 
 | 
 | 
 
DSC00157
 
Instructions state that rod should be reamed to 0.375" but it needed to be reamed out 0.428" to fit push rod.
 
Date: 09/03/2015
 
Views: 67137
 
 
 | 
 |