|
|
YouTube Channel
I've started a YouTube channel to vlog my build progress. Come check it out and leave a message!https://www.youtube.com/watch?v=OFgPUfHvLDE&list=PL2HSwhQop_QOThtzPUa_zLaMRj7qWyOv3
Date: 07/17/2021
Views: 329055
|
|
|
Orange part created in turbocad and printed on a 3D printer from ABS. Printer is a Prusa i3 X, cost is around $300.
Orange part created in turbocad and printed on a 3D printer from ABS. Printer is a Prusa i3 X, cost is around $300.
Date: 04/03/2016
Views: 31953
|
|
|
|
Wanted to make a copy of B16 to make the cuts on before I cut the actual B16 part.
Wanted to make a copy of B16 to make the cuts on before I cut the actual B16 part.
Date: 04/03/2016
Views: 27185
|
|
|
This is the printer part showing the parts in place.
This is the printer part showing the parts in place.
Date: 04/03/2016
Views: 26220
|
|
|
|
Close up of the relief cut.
Close up of the relief cut.
Date: 04/03/2016
Views: 27079
|
|
|
Actual part.
Actual part.
Date: 04/03/2016
Views: 28635
|
|
|
|
20160403_160443.jpg
20160403_160443.jpg
Date: 04/03/2016
Views: 26744
|
|
|
20160403_160502.jpg
20160403_160502.jpg
Date: 04/03/2016
Views: 26470
|
|
|
|
DSC08803
Me and my Uncle Kim.
Date: 06/10/2012
Views: 30332
|
|
|
NEX_2013-11-12-37
N111EU at rest.
Date: 11/13/2013
Views: 63723
|
|
|
|
20141102_152814
Drilling out the screw. It would move. I'm removing this plate to patch later.
Date: 11/02/2014
Views: 33056
|
|
|
20141102_153539
Out. Ad you can see the screw is sill in the nut plate. it came out later.
Date: 11/02/2014
Views: 46386
|
|
|
|
20141102_154450
Gear cover removed, now for removing the throttle box. This is all prep work to patch up the mono wheel hole.
Date: 11/02/2014
Views: 45180
|
|
|
20141102_154504
Cut old fuel lines. Gona have to replace them anyways. Now I just need to remove the stop block where the gear handle went.
Date: 11/02/2014
Views: 44452
|
|
|
|
20141102_161000
template for new firewall.
Date: 11/02/2014
Views: 42786
|
|
|
20141102_161036
Everything looking good.
Date: 11/02/2014
Views: 39675
|
|
|
|
20141102_161049
20141102_161049.jpg
Date: 11/02/2014
Views: 36491
|
|
|
20141102_162118
Cut it out.
Date: 11/02/2014
Views: 168009
|
|
|
|
nex_2014_01_25_35
Dont judge me! You know you do it too. Anyways, was trying to see if my weight would cause the nose to come down. As you can see she likes being a tail dragger.
Date: 01/26/2014
Views: 28626
|
|
|
nex_2014_01_25_31
Starboard side, need to trim the bolt.
Date: 01/26/2014
Views: 25473
|
|
