|
|
dsc09039
Port side done after cure.
Date: 01/23/2013
Views: 19051
|
|
|
dsc08620
Removal of the mono firewall.
Date: 04/14/2012
Views: 38819
|
|
|
|
p1000727
p1000727.jpg
Date: 03/12/2012
Views: 11642
|
|
|
dsc09071
Uncle Kim glassing in Rib 2.
Date: 01/26/2013
Views: 19384
|
|
|
|
dsc08639
More of the same. I was going to cut the carpet and form it to the ribs and staple it in place but decided that was just a time vampire and pointless since the airframe is holding it in place.
Date: 04/15/2012
Views: 25025
|
|
|
dsc09044
Port side being keyed.
Date: 01/23/2013
Views: 18132
|
|
|
|
dsc09067
dsc09067.jpg
Date: 01/25/2013
Views: 19426
|
|
|
dsc08401
I see you!
Date: 03/25/2012
Views: 28440
|
|
|
|
p1000636
p1000636.jpg
Date: 02/14/2012
Views: 11513
|
|
|
dsc08607
Starting to prep the bays for the tri-gear conversion.
Date: 04/10/2012
Views: 22097
|
|
|
|
dsc09022
Here you see I used bondo on the shims and screwed them down into the block. The shims made sure the guide was level. Also note the hole drilled in the Aluminum angle and the shim. This is where I fixed the guide for the curing stage to ensure nothing
Date: 01/22/2013
Views: 21768
|
|
|
dsc08962
Stb side. Need to do some clean up...
Date: 10/01/2012
Views: 22424
|
|
|
|
dsc08613
Unused Mono wheel components. I'll probably be selling these soon.
Date: 04/10/2012
Views: 32013
|
|
|
DSC08796
Put in the panel to dream a little. Don't really know what I'm going to do. Was thinking of keeping it low cost for the first panel and keeping it analog until I can get the cash mula for something better like glass/IFR. Also want to fill the hole where
Date: 06/05/2012
Views: 104932
|
|
|
|
dsc08602
Landing gear parts. The nose gear leg is having MOD 53 performed on it at my fauther in-laws.
Date: 04/10/2012
Views: 22638
|
|
|
dsc08603
Since I'm going to have to remove the mono wheel I dont have much of an edge to close in the big hole in the bottom. I'll have a better look at it once its a tri-gear.
Date: 04/10/2012
Views: 31534
|
|
|
|
p1000629
p1000629.jpg
Date: 02/14/2012
Views: 14397
|
|
|
dsc09051
Mix it up Kim! FYI I hate this scale from aircraft spruce, it times out in one min if your plugged in or not. I would have to tap the scale while Kim mixed. We were using masks due to being in an enclosed area and I'm very allergic to the hardener (bumm
Date: 01/24/2013
Views: 19311
|
|
|
|
nex_2013_08_24_01
Stb. side ribs 3 and 4 epibond in place with the 3 layups on all sides. At this point I was getting faster at doing layups however I only did one side at a time.
Date: 08/25/2013
Views: 17961
|
|
|
YouTube Channel
I've started a YouTube channel to vlog my build progress. Come check it out and leave a message!https://www.youtube.com/watch?v=OFgPUfHvLDE&list=PL2HSwhQop_QOThtzPUa_zLaMRj7qWyOv3
Date: 07/17/2021
Views: 323588
|
|
