|
|
Orange part created in turbocad and printed on a 3D printer from ABS. Printer is a Prusa i3 X, cost is around $300.
Orange part created in turbocad and printed on a 3D printer from ABS. Printer is a Prusa i3 X, cost is around $300.
Date: 04/03/2016
Views: 28608
|
|
|
dsc08601
Just a shot of the plane at home.
Date: 04/10/2012
Views: 28102
|
|
|
|
dsc08401
I see you!
Date: 03/25/2012
Views: 27524
|
|
|
dsc08610
Whats missing?
Date: 04/10/2012
Views: 27419
|
|
|
|
dsc08606
Old mass balance arm.
Date: 04/10/2012
Views: 27408
|
|
|
dsc08642
From the start the airframe was sitting 2.5 deg tail low and 0.1 deg to port. Not bad for just putting her on there. I jacked up the back of the trailer to get it as near to 0.0 as possible and also shifted the airframe latterly to turn that .1 to 0.0 a
Date: 04/15/2012
Views: 27251
|
|
|
|
dsc08403
Bill helping me out!
Date: 03/25/2012
Views: 26919
|
|
|
DSC08803
Me and my Uncle Kim.
Date: 06/10/2012
Views: 26781
|
|
|
|
nex_2014_01_25_35
Dont judge me! You know you do it too. Anyways, was trying to see if my weight would cause the nose to come down. As you can see she likes being a tail dragger.
Date: 01/26/2014
Views: 25943
|
|
|
Actual part.
Actual part.
Date: 04/03/2016
Views: 25183
|
|
|
|
dsc08664
The gell coat really gums up the sand paper. Still a bit more to remove.
Date: 04/22/2012
Views: 24944
|
|
|
dsc08662
The 10“ diameter from the pilot hole.
Date: 04/22/2012
Views: 24540
|
|
|
|
p1000473
p1000473.jpg
Date: 12/13/2011
Views: 24307
|
|
|
dsc08639
More of the same. I was going to cut the carpet and form it to the ribs and staple it in place but decided that was just a time vampire and pointless since the airframe is holding it in place.
Date: 04/15/2012
Views: 24288
|
|
|
|
p1000476
p1000476.jpg
Date: 12/13/2011
Views: 24287
|
|
|
dsc08661
Locating the center of the main gear hole. Used a pilot to be used to measure out the 10“ diameter on the bottom.
Date: 04/22/2012
Views: 24064
|
|
|
|
nex_2014_01_25_32
nex_2014_01_25_32.jpg
Date: 01/26/2014
Views: 24034
|
|
|
Wanted to make a copy of B16 to make the cuts on before I cut the actual B16 part.
Wanted to make a copy of B16 to make the cuts on before I cut the actual B16 part.
Date: 04/03/2016
Views: 23875
|
|
|
|
Close up of the relief cut.
Close up of the relief cut.
Date: 04/03/2016
Views: 23761
|
|
|
p1000472
p1000472.jpg
Date: 12/13/2011
Views: 23627
|
|
