http://europaowners.org/gallery2/v/DanBish/Rudder-Tailwheel/ en-us Gallery 2 RSS Module, version 1.1.8 Sun, 10 May 2026 03:54:18 +0000 120 http://europaowners.org/gallery2/d/51170-9/Rudder-Tailwheel.jpg http://europaowners.org/gallery2/v/DanBish/Rudder-Tailwheel/ http://europaowners.org/gallery2/v/DanBish/Rudder-Tailwheel/DSCF0044.jpg.html http://europaowners.org/gallery2/v/DanBish/Rudder-Tailwheel/DSCF0044.jpg.html ]]> danbish photo Tue, 17 Nov 2009 23:39:27 +0000 http://europaowners.org/gallery2/v/DanBish/Rudder-Tailwheel/DSCF0043.jpg.html http://europaowners.org/gallery2/v/DanBish/Rudder-Tailwheel/DSCF0043.jpg.html ]]> danbish photo Tue, 17 Nov 2009 23:39:27 +0000 http://europaowners.org/gallery2/v/DanBish/Rudder-Tailwheel/DSCF0041.jpg.html http://europaowners.org/gallery2/v/DanBish/Rudder-Tailwheel/DSCF0041.jpg.html
I'm getting full travel of the bell crank to both sides, but not of the rudder itself. Will make up a longer push rod and see if that's it. ]]> danbish photo Tue, 17 Nov 2009 23:39:27 +0000 http://europaowners.org/gallery2/v/DanBish/Rudder-Tailwheel/DSCF0042.jpg.html http://europaowners.org/gallery2/v/DanBish/Rudder-Tailwheel/DSCF0042.jpg.html
The key to this was getting the surface as absolutly uniform as possible. Install, remove, sand, repeat...]]> danbish photo Tue, 17 Nov 2009 23:39:27 +0000 http://europaowners.org/gallery2/v/DanBish/Rudder-Tailwheel/DSCF0038.jpg.html http://europaowners.org/gallery2/v/DanBish/Rudder-Tailwheel/DSCF0038.jpg.html ]]> danbish photo Tue, 17 Nov 2009 23:39:27 +0000 http://europaowners.org/gallery2/v/DanBish/Rudder-Tailwheel/DSCF0039.jpg.html http://europaowners.org/gallery2/v/DanBish/Rudder-Tailwheel/DSCF0039.jpg.html ]]> danbish photo Tue, 17 Nov 2009 23:39:27 +0000 http://europaowners.org/gallery2/v/DanBish/Rudder-Tailwheel/DSCF0037.jpg.html http://europaowners.org/gallery2/v/DanBish/Rudder-Tailwheel/DSCF0037.jpg.html ]]> danbish photo Tue, 17 Nov 2009 23:39:27 +0000 http://europaowners.org/gallery2/v/DanBish/Rudder-Tailwheel/DSCF0036.jpg.html http://europaowners.org/gallery2/v/DanBish/Rudder-Tailwheel/DSCF0036.jpg.html ]]> danbish photo Tue, 17 Nov 2009 23:39:27 +0000 http://europaowners.org/gallery2/v/DanBish/Rudder-Tailwheel/DSCF0035.jpg.html http://europaowners.org/gallery2/v/DanBish/Rudder-Tailwheel/DSCF0035.jpg.html
No binding here, but I did open up the hole in the sternpost a little bit, just to be sure. ]]> danbish photo Tue, 17 Nov 2009 23:39:27 +0000 http://europaowners.org/gallery2/v/DanBish/Rudder-Tailwheel/DSCF0034.jpg.html http://europaowners.org/gallery2/v/DanBish/Rudder-Tailwheel/DSCF0034.jpg.html ]]> danbish photo Tue, 17 Nov 2009 23:39:27 +0000