http://europaowners.org/gallery2/v/Begin-06-2003/album258/Fuse+wiring/Flowscan+wire+run/ en-us Gallery 2 RSS Module, version 1.1.8 Thu, 23 Apr 2026 18:03:40 +0000 120 http://europaowners.org/gallery2/d/86955-10/Flowscan+wire+run.jpg http://europaowners.org/gallery2/v/Begin-06-2003/album258/Fuse+wiring/Flowscan+wire+run/ http://europaowners.org/gallery2/v/Begin-06-2003/album258/Fuse+wiring/Flowscan+wire+run/DSCN7931.JPG.html http://europaowners.org/gallery2/v/Begin-06-2003/album258/Fuse+wiring/Flowscan+wire+run/DSCN7931.JPG.html
Wire entry is smooth and rounded.
Y10-08-05]]> rparigoris photo Sun, 02 Jan 2011 10:17:46 +0000 http://europaowners.org/gallery2/v/Begin-06-2003/album258/Fuse+wiring/Flowscan+wire+run/DSCN7930.JPG.html http://europaowners.org/gallery2/v/Begin-06-2003/album258/Fuse+wiring/Flowscan+wire+run/DSCN7930.JPG.html
Fill and glass cured / trimmed.
Y10-08-05]]> rparigoris photo Sun, 02 Jan 2011 10:17:46 +0000 http://europaowners.org/gallery2/v/Begin-06-2003/album258/Fuse+wiring/Flowscan+wire+run/DSCN7925.JPG.html http://europaowners.org/gallery2/v/Begin-06-2003/album258/Fuse+wiring/Flowscan+wire+run/DSCN7925.JPG.html
Here you can see pinched wire holder getting wires nice and flat. Wires are marked with printed on heatshrink markings. Wires are soldered together, yet if two tywrap hold downs are cut, enough service loop to work on and unsolder.
Y10-08-03]]> rparigoris photo Sun, 02 Jan 2011 10:17:46 +0000 http://europaowners.org/gallery2/v/Begin-06-2003/album258/Fuse+wiring/Flowscan+wire+run/DSCN7924.JPG.html http://europaowners.org/gallery2/v/Begin-06-2003/album258/Fuse+wiring/Flowscan+wire+run/DSCN7924.JPG.html
Used two pieces of carbon fiber reinforced yet still flexible model aeroplane Golden rod push rod inner tubing to hold wires flat by sandwiching with two Tywraps.
Y10-08-03]]> rparigoris photo Sun, 02 Jan 2011 10:17:46 +0000 http://europaowners.org/gallery2/v/Begin-06-2003/album258/Fuse+wiring/Flowscan+wire+run/DSCN7923.JPG.html http://europaowners.org/gallery2/v/Begin-06-2003/album258/Fuse+wiring/Flowscan+wire+run/DSCN7923.JPG.html
Here we are looking at Pilot side thigh support wire conduit. Two 914 flowscan 201B's are located under airbrake cover, run aft, soldered to extension wires held in place by two glassed in place Tywrap holders, then run up to top surface of thigh support.
Wires will be held by an Expancel fair and 2 thin model aeroplane glass plies over the top. Entrance for wires are filed nice and rounded and there will be 2 more 1/2" wide thin model aeroplane glass plies on the edge for added strength.
"WHEN" I have to remove these wires, could easily cut them out with a razor blade.
Y10-08-03]]> rparigoris photo Sun, 02 Jan 2011 10:17:46 +0000