|
dsc08605
When I received the plane it had a few areas of this green tape. I guess it was going to be used as a release agent for some sort of jig fabrication. I have found that this 3M stuff works very well.
Date: 04/10/2012
Views: 10393
|
|
|
dsc08612
Unused Mono wheel components. I'll probably be selling these soon.
Date: 04/10/2012
Views: 10359
|
|
|
dsc08960
Stb side after layups and peel ply removed.
Date: 10/01/2012
Views: 10358
|
|
|
p1000470
p1000470.jpg
Date: 12/09/2011
Views: 10285
|
|
|
2012-08-18_19-58-42_666
Port side. Same area as before just without the flash. Backlit from the inside to show areas with less material. This is before I did the belly layup per the manual.
Date: 08/19/2012
Views: 10117
|
|
|
E1
[quote="Bud Yerly"]"Make a glass cover that fits the hole out of three sheets of bid laid up on a flat surface. After cure, hold it up to the bottom of the plane and mark the contour. Cut and approximate the fit. It should be near level
Date: 10/05/2012
Views: 10109
|
|
|
dsc08961
Stb side two layers bid 10" and 8" peel ply removed
Date: 10/01/2012
Views: 10058
|
|
|
dsc08962
Stb side. Need to do some clean up...
Date: 10/01/2012
Views: 10039
|
|
|
dsc08603
Since I'm going to have to remove the mono wheel I dont have much of an edge to close in the big hole in the bottom. I'll have a better look at it once its a tri-gear.
Date: 04/10/2012
Views: 9965
|
|
|
dsc08642
From the start the airframe was sitting 2.5 deg tail low and 0.1 deg to port. Not bad for just putting her on there. I jacked up the back of the trailer to get it as near to 0.0 as possible and also shifted the airframe latterly to turn that .1 to 0.0 a
Date: 04/15/2012
Views: 9683
|
|
|
dsc08601
Just a shot of the plane at home.
Date: 04/10/2012
Views: 9622
|
|
|
2012-08-18_19-58-15_689
Port side. Red highlighted area shows area with little reinforcement on inside. This is before I did the belly layup per the manual.
Date: 08/19/2012
Views: 9596
|
|
|
dsc08625
Cutting out one of the ribs for the airframe. Going to use the mono trailer as the foundation of the jig. This will make is easy to level the airframe when getting ready for the trr-gear conversion. How do you like my work bench?
Date: 04/14/2012
Views: 9489
|
|
|
p1000469
p1000469.jpg
Date: 12/09/2011
Views: 9442
|
|
|
me_europa
Me in front of my Uncles Europa Classic late 90's in Borrego Springs, CA.
Date: 05/22/2012
Views: 9427
|
|
|
dsc08626
Put in a 2x4 in the main wing spar tunnel and located the pins. This was only used to aid in keeping the plane from tipping.
Date: 04/14/2012
Views: 9419
|
|
|
dsc08613
Unused Mono wheel components. I'll probably be selling these soon.
Date: 04/10/2012
Views: 9359
|
|
|
dsc08966
Port side LG socket hole.
Date: 10/01/2012
Views: 9164
|
|
|
20141102_152814
Drilling out the screw. It would move. I'm removing this plate to patch later.
Date: 11/02/2014
Views: 8839
|
|
|
dsc08614
Anybody know a easy way to remove this rust?
Date: 04/10/2012
Views: 8721
|
|