|
dsc09035
Rib one after cure of 420 and peel ply removed. Think we used 112g of 420 here due to the odd angle.
Date: 01/23/2013
Views: 6531
|
|
|
dsc09036
Rib one port side again used around 112g of 420 cured at 78f for 12 hours.
Date: 01/23/2013
Views: 7059
|
|
|
dsc09037
Making a template for rib 2. Do yourself a favor and do not use the templates in the manual you will end up waisting your plywood, just make your own.
Date: 01/23/2013
Views: 7174
|
|
|
dsc09018
Started to make the axle jig. Used a simple setup of first taking large flat blocks of wood and caulking it to the floor somewhere over FS70. Then that allows me to fix the aluminum angle with a single screw once in its final position.
Date: 01/10/2013
Views: 8033
|
|
|
dsc09019
Trash can is the best way to hold the landing gear legs.
Date: 01/10/2013
Views: 7002
|
|
|
dsc09020
Bill helping by putting a good key on the sockets.
Date: 01/22/2013
Views: 6802
|
|
|
dsc08967
Little clean up required on Port side.
Date: 10/01/2012
Views: 8374
|
|
|
dsc08965
Port side after layups and peel ply removed. Notice shape of hole for the angle of the LG socket. I wrapped the LG socket with sandpaper and used it to form the hole.
Date: 10/01/2012
Views: 8517
|
|
|
dsc08966
Port side LG socket hole.
Date: 10/01/2012
Views: 9135
|
|
|
dsc08963
Port side. LG socket fitting.
Date: 10/01/2012
Views: 8047
|
|
|
dsc08964
Port side. Fitting of LG socket.
Date: 10/01/2012
Views: 7874
|
|
|
dsc08960
Stb side after layups and peel ply removed.
Date: 10/01/2012
Views: 10319
|
|
|
dsc08961
Stb side two layers bid 10" and 8" peel ply removed
Date: 10/01/2012
Views: 10036
|
|
|
dsc08962
Stb side. Need to do some clean up...
Date: 10/01/2012
Views: 10018
|
|
|
photo (2)
Small area to work in. Back was killing me after that job. can't wait to give my back the same treatment when doing the ribs and starboard side.
Date: 08/20/2012
Views: 11827
|
|
|
photo (1)
Bad pic, but shows the end of the reinforcement layups (port side).
Date: 08/20/2012
Views: 11131
|
|
|
photo
No pictures of the progress of putting in the LG layups on the port side. Here I am putting down the peel ply.
Date: 08/20/2012
Views: 13661
|
|
|
2012-08-18_19-58-42_666
Port side. Same area as before just without the flash. Backlit from the inside to show areas with less material. This is before I did the belly layup per the manual.
Date: 08/19/2012
Views: 10084
|
|
|
2012-08-18_19-58-15_689
Port side. Red highlighted area shows area with little reinforcement on inside. This is before I did the belly layup per the manual.
Date: 08/19/2012
Views: 9578
|
|
|
DSC08800
starboard side
Date: 06/05/2012
Views: 8437
|
|